furuno ls4100 fish finder manual

WATER TYPE: Choose the water type with which to use the LS-4100, from Salt or Fresh. KEY BEEP: Turn key beep on or off. BATT VOLTAGE: Turn the battery voltage indication (appears at the top right corner on the screen) on or off. Page 3 BASIC RANGE 1 - BASIC RANGE 8: Set range of each of the eight basic. Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Checking the items listed in the table below monthly will help keep your equipment in good shape for years to come. For any NG, request service. (A special connector is required to test the NMEA port. Nothing appears if no connector is connected.) 5. When choosing a location keep the following in mind: Keep the display unit out of direct sunlight. For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. This may require a certain amount of experimentation for fine tuning at high cruising speeds. 4. Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces. Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of the boat. Mark this mounting hole. 5. If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover. Position the cover over the cable where it enters the hull. Refer to the interconnection diagram to connect cables. Leave slack in cables to facilitate checking and maintenance. The transmission speed for both input and output is 4800 bps. Data is output at two-second intervals. Input data sentences. Off: Outputs the data sentences of LS-4100 only. On: Outputs the data sentences of LS-4100 and sentences which are input from other equipment. 6. To restore normal operation, turn off the power and then turn it on again.

• furuno ls4100 fish finder manual, furuno ls4100 fish finder manual pdf, furuno ls4100 fish finder manual download, furuno ls4100 fish finder manual instructions, furuno ls4100 fish finder manual free.

Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer. WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. FURUNO will assume no responsibility for any damage associated with improper installation. Use the specified power cable. The main features of the LS-4100 are Bright 5-inch monochrome LCD gives excellent readability even in broad daylight. Automatic function permits unattended adjustment of range and gain. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation and displays program number. The time remaining until power is turned off is counted down on the screen. The lower the frequency of the signal, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. 200 kHz The higher the frequency of the ultrasonic signal the better the. This mode is useful for determining bottom contour. When the bottom depth increases, the display shift to keep the bottom echo at the lower part of the screen. Page 1 or Page 2 of the main menu appears depending on the page last used. The auto mode in use is shown as (Auto-Fishing) or (Auto-Cruising) at the top left corner on the screen. Note: When in the auto mode, SHIFT and CLUTTER cannot be adjusted manually. Shifting the range The basic range may be shifted up or down in the manual mode as follows: Window can be shifted up and down to select the depth. Display Range and display shift concept 1. Depth, temperature, speed setting window 10.When TLL or FURUNO-TLL is selected at TLL OUTPUT on the System menu, the latitude and longitude position at the cursor is output to the navigator. GPS 2D: 2D (dimension) GPS position fix GPS 3D: 3D GPS fix GPS W2D: 2D WAAS position fix. Fish school clearly shown White line 52.6 52.6 White Line OFF White Line ON (Mesh) How white line works. SYSTEM MENU LANGUAGE English DEPTH UNIT: ft.

We are confident you will see why the. FURUNO name has becomeFor over 50 years FURUNO Electric. Company has enjoyed an enviableThe main features of the LS-4100 areThis equipment is designed andHowever, no machine can perform itsTemperature and Arrival. (Speed andWe would appreciate hearing from you,Thank you for considering andGPS NavigatorWind Indicator. Power supplySpeed sensor. TransducerEquipment lists. Standard supply. Name. Display Unit. Transducer. Triducer (transducer. Installation MaterialsCode No. Qty. RemarksSpare PartsTemplate. C22-00301 (000-146-981, for flush mount). C22-00302 (000-146-982, for bulkhead). Optional equipment. Conversion Cable. Speed Sensor. Inner Hull Kit S. TypeQty. RemarksThru-hull typeCursor Pad. Selects menu items;Selects display mode.Selects basic display range.Display unit. How to remove the hard cover. Place your thumbs at the center of theThe unit beeps, the startup screenContact your dealer.) You mayStart-up screen. To turn off the power, press and holdFrequency. Seven displays are available: singleNote: The example screens shown inContrast, BrillianceMinMinMaxDual frequency displayThe 50 kHz picture appears on the left;The sounder uses ultrasonic signals toThe lower theThe higher the frequency of theMarker-zoom displayThis mode expands chosen area of theFrequency and coverage area. Picture Advance Speed. ModeSingle frequency display. FrequencyMarkerEach barZoomedTransmission 20. Fish. School Line. FishMarker-zoom displayNav data displays. This mode expands bottom and bottomRANGE of the SYSTEM menu. ThisThe nav data displays appear on the leftYou can display between two and fourDATA-2” in paragraph 2.1 to choose theZoomBottom-zoom displayBottom-zoom display. Trip meter. Bottom-lock displayThe bottom-lock display provides aThis mode is useful for detecting bottomNAV DATA-1 displayThis sectionSample NAV DATA displaysBottom displayed flat. Bottom-lock displayProcedure. Off. Cruising. Fishing. The LS-4100 has three menus: Main.

Note: WAAS is currently in the developmental phase. During the developmental phase the reliability and availability of the WAAS signal cannot be guaranteed. Therefore, any position data should be verified against other sources to confirm reliability. All rights reserved. SYSTEM OVERVIEW. ivAdjusting Display Contrast. Brilliance.2Speed.8Cleaning the Display Unit. 21. Transducer Maintenance. 21. Replacing the Fuse. 21. Battery Voltage Alert. 21. Troubleshooting. 22. Diagnostics. 22. Test Pattern. 23. Memory Clear. 23Thru-hull Mount Transducer. 24. Transom Mount Transducer. 26. Inside-hull Transducer. 28. Optional Triducer. 29. Optional WaterDo no turn on the equipment with theThere are no uer-serviceable partsThe transducer may be damaged. Do not disassemble or modify theThe picture is not refreshed whenFire, electrical shock or serious injuryManeuvering the vessel in this conditionImmediately turn off the power at theUse the proper gain setting. Incorrect gain may produce wrong depthContinued use of the equipment canFURUNO agent for service.Use the proper fuse. The high quality LCD shows 99.99%Fuse rating is shown on the equipment. Use of a wrong fuse can result inA warning label is attached to theIf the label is missing or damaged,Grounding may result.Name. Warning Label. Type: 02-146-1022. Code No.: 100-306-050. Safety Instructions for the InstallerDo not install the equipment whereFire or electrical shock can result if thePerformance will be affected. The following are guidelines forBe sure no water leaks in at the transducer or sensor mounting location.Water leakage can sink the vessel. AlsoThe sheath of the cable is made ofDo not turn on the equipment with theUse the specified power cable. The transducer may be damaged. Use of other power cable may result inObserve the following compass safeStandardDisplaySteeringOwners. Features. The FURUNO LS-4100 is a dualComprised of a display unit and aCongratulations on your choice of the. FURUNO LS-4100 5” Echo Sounder.

Alarm menuWater temperature alarm: The waterOff. On. Inside. Outside. Fish, Arrival, Temp, Speed. Bottom Alarm Alarm Types. Speed alarm: The speed alarm alertsAlarm options. Off: Alarm off, On: Alarm on. Inside: Alarm generated whenOutside: Alarm generated whenArrival alarm: The arrival alarm alertsActivating an alarmDepthTemperature. Speed. Alarm range. Depth, temperature, speed settingStartingAlarm range markerHow the alarm works. Note: To disable an alarm, choose OffSilencing the buzzer. The buzzer sounds and the appropriateYou can silence theWeak. Medium. Strong. Fish level optionsNote: The audio and visual alarms areWeak: Weak echoes (weakest toneMedium: Medium strength echoesStrong: Strong echoes (darkest toneWaypoints may be used to:Note: Requires latitude and longitudeNote: If there is no position data theCheck the navigator.Waypoint data display. Note: If you attempt to enter 13thTLL or FURUNO-TLL is selected at. TLL OUTPUT on the System menu,A vertical line marks location. Further,The name mayLIST from page 2 of the menu. Erasing waypointsNote: You cannot erase a waypointSet a destination waypoint to find range,Time to Go digital display. Erase? New waypoint window, name entryOffLIST from page 2 of the menu.Waypoint listDisplaysFour-data. Two-dataItems displayable in (1) - (3): depth, position,Items displayable in (4) - (9): depth, position,NAV DATA-1 or 2 display, whicheverNAV DATA SETUP window.NAV DATA SETUP windowNote: You can choose the number ofNAV DATA-1 and NAV DATA-2 on the. System menu.XTE scaleName. Range,Rng 0.19nm. XTE 0.00nmCourse. DestinationBearing toDepthCourse. Brg. Wind Dir.Trip meterWind Speed. SpeedOdometerNO FIX: Position cannot be found. GPS 2D: 2D (dimension) GPS position fix. GPS 3D: 3D GPS fix. GPS W2D: 2D WAAS position fix. GPS W3D: 3D WAAS position fix. Note 1: Nav data is updated with someNote 2: When data is lost 120 sec., theNAV data display-2.

System and Installation. Below is theAuto mode options windowSince “Cruising” uses a higher clutterChoosing the manual mode. The auto mode in use is shown asNote: When in the auto mode, SHIFTRange offset. To display the bottom tail in detail in theChoosing range. The basic range and range shiftingNote that if the basic range isChoosing basic range. The basic range may be chosen withDefault ranges. Gain offset. Gain offset lets you override automaticUnitMax. Auto gain offset window. Basic RangeUse the proper gain setting. Incorrect gain may produce wrong depthShifting the range. The basic range may be shifted up orWindow can beGain too high Gain proper Gain too low. Examples of proper and improper gainDisplay. Range and display shift conceptMaxShift windowNote: The picture may not be displayedThe VRM (Variable Range Marker)Fast. Slow. Picture and picture advancement speedHow to measure depth with the VRMAdvance Speed. The picture advance speed determinesNote that theManeuvering the vessel in this conditionInterferenceLevel Noise. Interference from other acousticTo suppress interference, do theMedium, or High (highest).Low intensity “speckles” may appearCLUTTER on the menu. When theTo suppress lowTo turn off low-level noiseInterference fromElectrical interference. Forms of interference. Turn the noise limiter off when noClutter appearanceEchoesThis display shows echoes at eachIt is useful forSediment in the water or reflectionsWeakNote: In the dual frequency display, the. A-scope display is only available withSingle frequency display. Appearance of weak echoesLEVEL from page 1 of the menu.High (highest).StrongStrongA-scope displayA-scope presentation type desired. Normal: Display shows echoes atPeak: Peak-hold amplitude picture.To turn off the signal level function. To turn off the A-scope display,Alarm description. The LS-4100 has six conditions whichBottom alarm: The bottom alarm alertsPageInsideGray characters mean alarm is inactive.

SealantChoosing the mounting location. Coating transducer faceChecking the installationAuto mode.Triducer 525ST-MSDRelease Bracket 525ST-PWD isPre-test for speed and temperature. Final preparation. Support the transducer with a piece ofLet the transducer dry 24-72 hours. Connect the sensor to the instrumentCheck for aTools and materials needed. Scissors. Masking tape. Safety goggles. Dust mask. Electric drill. Drill bit for. Fiberglass hull: chamfer bitScrewdrivers. Straight edge. Marine sealant. Pencil. Zip-ties. Water-based antifouling paintMounting location on single drive boat. Note 4: For twin drive boat, mountMounting location. To ensure the best performance, theMount the sensor close to the centerlineInstallation of bracketAllow adequate space above theHeight withoutHeight withP66 Installation templateHeight. Height required at mounting locationNote 1: Do not mount the sensor in anNote 2: Avoid mounting the sensorNote 3: For single drive boat, mountAlign arrow with bottom of transom. Align template vertically. Deadrise angle. Slope of hullAlign template arrow withPositioning the templateFiberglass hull: Minimize surfaceIf a chamfer bit or countersink bit isSkip to step 3 in “Adjusting”. Other angles: The shim is required. Skip to step 2 of “Adjusting”. If you do not know the transom angle,NOT tighten the screws completelyAdjustingSensor position and transom angle. Note: Do not position the bow of thePosition the shim with the taperedApply a marine sealant to theNote: Do not position the sensorStep 3. Step 4Attaching the sensor to the bracketCable cover. CableCable routing. Route the sensor cable over theVertical adjustment and cable routing. Attaching the sensor to the bracketStep 1. Never cut the cable or remote theAlways wear safety goggles and a dustCheck for obstructions such as trimMark the location with a pencil. DrillStep 2. Latch. PivotRetainingSlot (2)Position theIf used, pushSensor.

ST-02MSB and ST-02PSB, which areInstall them asMounting considerations. Choose a suitable mounting locationLocknut. The ground wire (1.25 sq or more, localThe signal line ground is isolated fromTherefore, whenIf excessiveDo not use an “open” type lug (Refer to the interconnection diagram toOptional equipment. POWER connector. The power supply port is commonlyNote: The fuse holder contains a springFuse holder. Connector. ColorHow to fix fuse holderSentenceBind tape ends withFrom tape from unraveling.FromSentence. DBT (Ver. 1.5). Connection of converterDPT (Ver. 2.0, Ver.Sentences. Input data sentences. MeaningMeaning. Depth belowDepth. Water temperature. RecommendedWater speed andTarget position,The tables below show the dataSentence. Wind speed andRecommendedLORAN-C data. RecommendedRecommendedWater speed andCourse over groundCross track errorNMEA port setupThe POWER port can function as anInstallation menu appears.WAAS” (in the Installation menu) andInstallation MenuInstallation menu appears.SIMULATION: The simulation modeMIX options window. Choose On to output input data.Off: Outputs the data sentences of. LS-4100 only. On: Outputs the data sentences of. LS-4100 and sentences which areIf the bottomAnd if the bottom level is too high theGPS WAAS: Chooses how to use the. WAAS signal when connecting with a. WAAS receiver, for example GP-320B. Note: WAAS is currently in theOff. WAAS options windowBottom level. Bottom level displayNote: The mode must be other thanTransmit Method. Output Power. TX Rate. Pulse-lengthMarker zoom, Bottom zoom, Bottom-lockRange. Range SettingDisplayBottom-lock expansion: 3 to 10 m. Sectional expansion: 2 to 50 mNishinomiya, Japan. Telephone:Printed in Japan. PUB.No. OME-23710. There are no uer-serviceable parts The transducer may be damaged. inside. The picture is not refreshed when Do not disassemble or modify the picture advancement is stopped. equipment.

This section describes the menu itemsPage 1The white line feature displays theTwo picture color arrangements areNote: To reset the odometer to zero,Mesh as appropriate. “Mesh” paintsIf the gain is too high or too low, or theHow white line worksPage 2RESET? from page 2 of the menu.Page 1. LANGUAGE: The system language isBATT VOLTAGE: Off. SPEED UNIT: Choose unit of speedPage no.WIND UNIT: Choose unit of wind speedTEMP SOURCE: Own. SPEED SOURCE: OwnOwn temp. TEMP UNIT: Choose unit ofFahrenheit. Requires temperature data. TEMP GRAPH: Turns the waterScaleZOOM MARKER: OnGraphNAV DATA-1, -2: Choose the number ofWATER TYPE: Choose the water typeSalt or Fresh.Apparent: The direction (in relation toTrue: The speed and direction (inKEY BEEP: Turn key beep on or off. BATT VOLTAGE: Turn the batteryWhen on it replaces the picture advancePage 2. NAV DISPLAY: Choose the nav data toYou may chooseTRIP SOURCE: Choose speed sourceTEMP SOURCE: Choose source ofNav window. SPEED SOURCE: Choose source ofNMEA0183: Choose NMEA version ofTEMP CALIB.: If the water temperaturePage 3Note 1: All default basic ranges areNote 2: A range may not be lower thanFor example, ifZOOM RANGE: Choose the range toZOOM MARKER: The zoom markerMaintenanceDo not open the equipment. Only qualified personnel should workRegular maintenance is essential forChecking. ItemThe fuse in the power cable protects theAction. TransducerCheck cable for damage. Power cable,Check that they are tightlyDisplay unitCheck for corrosion. CleanUse the proper fuse. Power supplyCheck voltage. If out ofFuse rating is shown on the equipment. Use of a wrong fuse can result in fire andUnit. A battery icon appears when the batteryDust or dirt on the display unit can beIf desired, aUse special care when cleaning the. LCD since it scratches easily. Do notBattery icon and meaning. Icon. Meaning. Voltage is lower than 10 VDC. If theVoltage is higher than 16.5 VDC.

If theThe table below provides basicIf you feel your unit is not workingTroubleshooting tableInstallation menu appears.Installation MenuLevel barTemperature. Battery Voltage. TemperaturePower: 12.4 V. Only when GP-310B is connected. Test displayOK or NG (No Good). For any NG,Nothing appears if no connector isThe memory can be cleared to startThis feature tests for proper display ofInstallation menu.Mounting considerations. See the instructions on the bulkhead orThe display unit can be installed on aTransducerStandard compass: 0.4 meters. Steering compass: 0.3 meters. Transducer mounting location. The thru-hull mount transducerThe performance of this sounder isNoise from the propellers alsoDesktop, overhead mountingTypical thru-hull mountRubber Washer. Fairing. Block. HullRubber. WasherWasher. Flat Hull. Thru-hull mount transducer dimensions. Typical thru-hull mountAcceptable transducer mountingProcedure for installing theFabricate the fairing block as shownSuitable transducer mounting locationsDO NOT paint the transducer. Performance will be affected.Transducer. The transom mount transducer is veryDo not use this method on an inboardLower Half. Saw along slopeConstruction of fairing blockBe sure that the transducer isNote: Do not over-stress the stuffingDeep-V. HullInstalling the 520-5PWD on a flat hull. A suitable mounting location is at leastTransducer preparation. Before putting the boat in water, wipeM5 x 14. No. 2Transom mount transducer,No.1. M5 x 14Parallel with hull. Hull. TransomTape. Mount at the stripe. Transom. Transom mount transducer,StripeInstalling the transom mountThis method is employed on deep-VInstalling the 525-5PWD. Referring to “Installing the 520-5PWD”Bracket. TransducerHullEpoxy material. CenterlineTransducerTransducerInside-hull transducer mounting location. Attaching the transducer. The thru-hull mount transducerLightly roughenNecessary tools. You will need the following tools. Remarks on installationTransducer. Silicone.

Maneuvering the vessel in this condition Fire, electrical shock or serious injury may result in a dangerous situation. can result. Use the proper gain seFire or electrical shock can result if the Performance will be affected.Water leakage can sink the vesselFURUNO LS-4100 5? Echo Sounder. Comprised of a display unit and a We are confident you will see why the transducer, the LS-4100 displays FURUNO name has become underwater conditions on a bright 5-inch synonymous with quality and reliability.Qty Remarks Display Unit LS-4100 ? 1 520-5PSD 000-Selects display mode. GAIN Adjusts gain. RANGE Selects basic display range. Momentary press: Adjusts display contrast and brilliance. Display unit How to remove This The sounder uses ultrasonic signals to display is useful for comparing the same detect bottom conditions. The lower the picture with two different transmitting frequency of the signal, the wider the frequencies.Data other than depth RANGE of the SYSTEM menu. This requires appropriate sensor.When the bottom depth You can display between two and four increases, the display shift to keep the items in a nav data display and choose bottom echo at the lower part of the the item and ordPage 1 or Page 2 of the menu, or press Shifting the range The basic range mayThis is mainly due electronic equipment on your boat may to sediment in the water or noise. These show itself on the display as shown in can be suppressed by adjusting the figure below. CLUTTER on the menu. When the To suppress interference, do the automatic mode is on, clutter is following: automatiWeak Note: In the dual frequency display, the echoes A-scope display is only available with the high frequency displ. Do no turn on the. Page 4 Safety Instructions for the InstallerPage 5: FOREWORD FOREWORD. A Word to LS-4100 Features. Owners The FURUNO LS-4100 is a dual. Congratulations on your choice of the frequency. Page 6: SYSTEM OVERVIEW SYSTEM OVERVIEW.

System configurationPage 10 Bottom-zoom display Nav data displays. This mode expands bottom and bottom The nav data displays appear on the leftThe LS-4100 has three menus: Main. System and Installation.The auto mode in. Page 13 1000ft Adjusting the gainThe VRM (Variable Range Marker)Interference from other acoustic Low intensity “speckles” may appearSediment in the water or reflections transmission. Page 17 1.14 Alarms MENU from page 2 on the menu.Page 22 DIGITAL DISPLAYSThe System menu mainly consists of 2.1 System MenuPage 26 SPEED CALIB.: If the speedMarine life on the transducer. Page 28 3.6 Troubleshooting 3.7 Diagnostics. The table below provides basic If you feel your unit is not workingMounting considerationsPage 31 submerged, even when the boat is Typical thru-hull mountPage 32 Hole for BOW DO NOT paint the transducer.Screwdrivers. Straight edgeThe installation menu mainly contains (NMEA PORT, NMEA MIX)Page 43 GPS WAAS: Chooses how to use the BOTTOM LEVEL: If the depth. WAAS signal when connecting with a indication is. Page 44: SPECIFICATIONS SPECIFICATIONS OF ECHO SOUNDER LS-4100. Do no turn on the equipment with the transducer out of water. There are no uer-serviceable parts inside. Do not disassemble or modify the equipment. The picture is not refreshed when picture advancement is stopped. Fire, electrical shock or serious injury can result. Maneuvering the vessel in this condition may result in a dangerous situation. Page 4 Safety Instructions for the Installer WARNING CAUTION Turn off the power at the switchboard before beginning the installation. Do not install the equipment where air bubbles and noise are present.

furuno ls 4100 user manual

WATER TYPE: Choose the water type with which to use the LS-4100, from Salt or Fresh. KEY BEEP: Turn key beep on or off. BATT VOLTAGE: Turn the battery voltage indication (appears at the top right corner on the screen) on or off. Page 3 BASIC RANGE 1 - BASIC RANGE 8: Set range of each of the eight basic. Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Checking the items listed in the table below monthly will help keep your equipment in good shape for years to come. For any NG, request service. (A special connector is required to test the NMEA port. Nothing appears if no connector is connected.) 5. When choosing a location keep the following in mind: Keep the display unit out of direct sunlight. For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. This may require a certain amount of experimentation for fine tuning at high cruising speeds. 4. Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces. Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of the boat. Mark this mounting hole. 5. If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover. Position the cover over the cable where it enters the hull. Refer to the interconnection diagram to connect cables. Leave slack in cables to facilitate checking and maintenance. The transmission speed for both input and output is 4800 bps. Data is output at two-second intervals. Input data sentences. Off: Outputs the data sentences of LS-4100 only. On: Outputs the data sentences of LS-4100 and sentences which are input from other equipment. 6. To restore normal operation, turn off the power and then turn it on again.

• furuno ls 4100 user manual, furuno ls 4100 manual, furuno ls 4100 manual pdf, furuno ls 4100 manuale italiano, furuno ls 4100 user manual, furuno ls 4100 user manual pdf, furuno ls 4100 user manual download, furuno ls 4100 user manual instructions, furuno ls 4100 user manual free.

Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer. WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. FURUNO will assume no responsibility for any damage associated with improper installation. Use the specified power cable. The main features of the LS-4100 are Bright 5-inch monochrome LCD gives excellent readability even in broad daylight. Automatic function permits unattended adjustment of range and gain. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation and displays program number. The time remaining until power is turned off is counted down on the screen. The lower the frequency of the signal, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. 200 kHz The higher the frequency of the ultrasonic signal the better the. This mode is useful for determining bottom contour. When the bottom depth increases, the display shift to keep the bottom echo at the lower part of the screen. Page 1 or Page 2 of the main menu appears depending on the page last used. The auto mode in use is shown as (Auto-Fishing) or (Auto-Cruising) at the top left corner on the screen. Note: When in the auto mode, SHIFT and CLUTTER cannot be adjusted manually. Shifting the range The basic range may be shifted up or down in the manual mode as follows: Window can be shifted up and down to select the depth. Display Range and display shift concept 1. Depth, temperature, speed setting window 10.When TLL or FURUNO-TLL is selected at TLL OUTPUT on the System menu, the latitude and longitude position at the cursor is output to the navigator. GPS 2D: 2D (dimension) GPS position fix GPS 3D: 3D GPS fix GPS W2D: 2D WAAS position fix. Fish school clearly shown White line 52.6 52.6 White Line OFF White Line ON (Mesh) How white line works. SYSTEM MENU LANGUAGE English DEPTH UNIT: ft.

Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. Contact a FURUNO agent for service. Use of a wrong fuse can result in damage to the equipment. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer. Also confirm that the transducer and sensor will not loosen by ship's vibration. The installer of the equipment is solely responsible for the proper installation of the equipment. FURUNO will assume no responsibility for any damage associated with improper installation. For this reason do not paint the cable. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. This dedication to excellence is furthered by our extensive global network of agents and dealers. However, no machine can perform its intended function unless operated and maintained properly. Please carefully read and follow the recommended procedures for operation and maintenance. Comprised of a display unit and a transducer, the LS-4100 displays underwater conditions on a bright 5-inch monochrome LCD. The range scale and gain automatically change to display the bottom in the darkest gray tone on the lower half of the screen. Contact your dealer.) You may The time remaining until power is turned off is counted down on the screen. The screen you see depends on your system configuration and equipment settings. Press for 200 kHz. The lower the frequency of the signal, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. For this reason the 200 kHz frequency is ideal for detailed observation of fish schools. This display is useful for comparing the same picture with two different transmitting frequencies. This mode is useful for determining bottom contour. When the bottom depth increases, the display shift to keep the bottom echo at the lower part of the screen.

Note: WAAS is currently in the developmental phase. During the developmental phase the reliability and availability of the WAAS signal cannot be guaranteed. Therefore, any position data should be verified against other sources to confirm reliability. All rights reserved. Do no turn on the. Page 4 Safety Instructions for the InstallerPage 5: FOREWORD FOREWORD. A Word to LS-4100 Features. Owners The FURUNO LS-4100 is a dual. Congratulations on your choice of the frequency. Page 6: SYSTEM OVERVIEW SYSTEM OVERVIEW. System configurationPage 10 Bottom-zoom display Nav data displays. This mode expands bottom and bottom The nav data displays appear on the leftThe LS-4100 has three menus: Main. System and Installation.The auto mode in. Page 13 1000ft Adjusting the gainThe VRM (Variable Range Marker)Interference from other acoustic Low intensity “speckles” may appearSediment in the water or reflections transmission. Page 17 1.14 Alarms MENU from page 2 on the menu.Page 22 DIGITAL DISPLAYSThe System menu mainly consists of 2.1 System MenuPage 26 SPEED CALIB.: If the speedMarine life on the transducer. Page 28 3.6 Troubleshooting 3.7 Diagnostics. The table below provides basic If you feel your unit is not workingMounting considerationsPage 31 submerged, even when the boat is Typical thru-hull mountPage 32 Hole for BOW DO NOT paint the transducer.Screwdrivers. Straight edgeThe installation menu mainly contains (NMEA PORT, NMEA MIX)Page 43 GPS WAAS: Chooses how to use the BOTTOM LEVEL: If the depth. WAAS signal when connecting with a indication is. Page 44: SPECIFICATIONS SPECIFICATIONS OF ECHO SOUNDER LS-4100. At InstructionsManuals.com we have gathered together the manuals to make it easier for you to locate them. We take no responsibility for the validity of the information available in each manual nor do we have any affiliation with the brands nor their products. (Sounders Furuno).

The picture is not refreshed when picture advancement is stopped. Fire, electrical shock or serious injury can result. Maneuvering the vessel in this condition may result in a dangerous situation. Page 4 Safety Instructions for the Installer WARNING CAUTION Turn off the power at the switchboard before beginning the installation. Do not install the equipment where air bubbles and noise are present. Fire or electrical shock can result if the power is left on. Performance will be affected. The following are guidelines for handling of the transducer cable. Be sure no water leaks in at the transducer or sensor mounting location. - Do not locate near oils and fuels. - Locate it in a safe place. Page 5 FOREWORD A Word to LS-4100 Owners Features The FURUNO LS-4100 is a dual frequency (50 kHz and 200 kHz) monochrome LCD echo sounder. Comprised of a display unit and a transducer, the LS-4100 displays underwater conditions on a bright 5-inch monochrome LCD. Congratulations on your choice of the FURUNO LS-4100 5” Echo Sounder. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. Page 6 SYSTEM OVERVIEW System configuration MODE MENU ESC DISPLAY UNIT LS-4100 GAIN RANGE MARK ECHO SOUNDER LS-4100 POWER BRILL Note: Contact your dealer for connection of other equipment. Page 7 1. OPERATION 1.1 Control Description Cursor Pad Selects menu items; shifts VRM. Selects display mode. GAIN Adjusts gain. Selects basic display range. Momentary press: Adjusts display contrast and brilliance. Page 9 Single frequency display Dual frequency display 50 kHz The 50 kHz picture appears on the left; the 200 kHz picture on the right. This display is useful for comparing the same picture with two different transmitting frequencies. The sounder uses ultrasonic signals to detect bottom conditions. The lower the frequency of the signal, the wider the detection area. This mode is useful for determining bottom contour.

This mode is useful for detecting bottom fish. Data other than depth requires appropriate sensor. See paragraph 1.16 to choose the items to display, “NAV DATA-1” and “NAV DATA-2” in paragraph 2.1 to choose the number of items to display. Below is the basic menu operating procedure. Page 1 or Page 2 of the main menu appears depending on the page last used. The example shown at the top of the right column is the options window for AUTO MODE. It works as follows: Since “Cruising” uses a higher clutter rejection setting than fishing, it is not recommended for fish detection - weak fish echoes may not be displayed. “Fishing” clearly displays weaker echoes. Note that if the basic range is changed the offset is returned to “0”. The gain selected is shown at the top of the screen as MANUAL appears at the top left corner on the screen. The basic range can be thought of as providing a “window” into the water column and range shifting as moving the “window” to the desired depth. Generally, use a higher gain setting for greater depths and a lower setting for shallower waters. When choosing a picture advance speed, keep in mind that a fast advance speed will expand the size of the fish school horizontally on the screen and a slow advance speed will contract it. Note that the picture is not refreshed when picture advancement is stopped. Therefore, use caution when steering the vessel under this condition. The fractions in the options window denote the number of scan lines produced per transmission.This is mainly due to sediment in the water or noise. These can be suppressed by adjusting CLUTTER on the menu. When the automatic mode is on, clutter is automatically rejected. To suppress low level noise in manual sounder operation, do the following. Do no turn on the equipment with the transducer out of water. There are no uer-serviceable parts inside. The transducer may be damaged. Do not disassemble or modify the equipment.

The procedure for this is shown later. Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of the boat. Fiberglass hull: Minimize surface cracking by chamfering the gelcoat. Note: Do not position the sensor farther into the water than necessary to avoid increasing drag, spray, and water noise and reducing boat speed. Tighten the screws. Attaching the sensor to the bracket 2. Insert the sensor’s pivot arms into the slots near the top of the bracket. 3. Page 39 4. Position the second cable clamp halfway between the first clamp and the cable hole. Mark this mounting hole. 5. If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover. Position the cover over the cable where it enters the hull. The signal line ground is isolated from the chassis ground, however the power line is not insulated. Therefore, when connecting eternal equipment having positive ground, do not ground the signal line to the chassis. If excessive noise shows on the screen, the ground may be inadequate. Sentence MWV RMA Connect to XDR port at rear of display unit RMB MJ-A10SPF RMC MJ-A6SRMD MJ-A10SRMD VHW VTG Tape connectors with vulcaninzing tape and then vinyl tape to waterproof them. Bind tape ends with cable ties to prevent From tape from unraveling. Page 42 4.9 Installation Menu NMEA port setup (NMEA PORT, NMEA MIX) The installation menu mainly contains items which are set at installation. Page 43 BOTTOM LEVEL: If the depth indication is unstable in automatic operation, or the bottom echo cannot be displayed in the darkest gray tone by adjusting the gain controls in manual operation, you may adjust the bottom echo level detection circuit, for both 50 kHz and 200 kHz, to stabilize the indication. Generally, lower the bottom level for inner hull installation where the receive level is too low. Printed in Japan PUB.No.

OME-23710 ( HIMA ) LS-4100 FIRST EDITION: MAR. There are no uer-serviceable parts The transducer may be damaged. inside. The picture is not refreshed when Do not disassemble or modify the picture advancement is stopped. equipment. Maneuvering the vessel in this condition Fire, electrical shock or serious injury may result in a dangerous situation. can result. Use the proper gain seFire or electrical shock can result if the Performance will be affected.Water leakage can sink the vesselFURUNO LS-4100 5? Echo Sounder. Comprised of a display unit and a We are confident you will see why the transducer, the LS-4100 displays FURUNO name has become underwater conditions on a bright 5-inch synonymous with quality and reliability.Qty Remarks Display Unit LS-4100 ? 1 520-5PSD 000-Selects display mode. GAIN Adjusts gain. RANGE Selects basic display range. Display unit How to remove This The sounder uses ultrasonic signals to display is useful for comparing the same detect bottom conditions. The lower the picture with two different transmitting frequency of the signal, the wider the frequencies.Data other than depth RANGE of the SYSTEM menu. This requires appropriate sensor.When the bottom depth You can display between two and four increases, the display shift to keep the items in a nav data display and choose bottom echo at the lower part of the the item and ordPage 1 or Page 2 of the menu, or press Shifting the range The basic range mayThis is mainly due electronic equipment on your boat may to sediment in the water or noise. These show itself on the display as shown in can be suppressed by adjusting the figure below. CLUTTER on the menu. When the To suppress interference, do the automatic mode is on, clutter is following: automatiWeak Note: In the dual frequency display, the echoes A-scope display is only available with the high frequency displ. Ask your question here. Provide a clear and comprehensive description of the issue and your question.

When the bottom depth increases, the display shift to keep the bottom echo at the lower part of the screen. The nav data displays appear on the left of the screen. Data other than depth requires appropriate sensor. Page 11 1.5 Menu Operating Procedure Off Cruising Fishing The LS-4100 has three menus: Main, System and Installation. Page 1 or Page 2 of the main menu appears depending on the page last used.Generally, use a higher gain setting for greater depths and a lower setting for shallower waters. Use the proper gain setting. It is useful for estimating the kind of fish school and bottom composition. Sediment in the water or reflections from plankton may be painted on the display in low intensity tones. Weak echoes Note: In the dual frequency display, the A-scope display is only available with the high frequency display. The cursor appears along with waypoint entry instructions. Page 25 BEARING: Ship’s course and bearing to a waypoint may be displayed in true or magnetic bearing. Magnetic bearing is true bearing plus (or minus) earth’s magnetic deviation. Requires bearing data. NAV DATA-1, -2: Choose the number of navigation data items to display on the nav data displays, from two, three or four items. Requires appropriate nav data. WATER TYPE: Choose the water type with which to use the LS-4100, from Salt or Fresh. Page 26 SPEED CALIB.: If the speed sensor-generated speed indication is wrong, you can correct it here, when “Own” is selected as speed source. Page 3 BASIC RANGE 1 - BASIC RANGE 8: Set range of each of the eight basic ranges. (Selectable range: 7 to 1500 ft) Note 1: All default basic ranges are restored whenever the depth unit is changed. Page 27 3. MAINTENANCE, TROUBLESHOOTING 3.3 Transducer Maintenance WARNING ELECTRICAL SHOCK HAZARD Marine life on the transducer face will result in a gradual decrease in sensitivity. Check the transducer face for cleanliness each time the boat is dry-docked.

Carefully remove any marine life with a piece of wood or fine-grade sandpaper. Do not open the equipment. Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Page 28 3.6 Troubleshooting 3.7 Diagnostics The table below provides basic troubleshooting procedures which the user may follow to restore normal operation. If you feel your unit is not working properly, conduct the diagnostic test to find the problem. If you cannot restore normal operation, contact your dealer for advice. For any NG, request service. (A special connector is required to test the NMEA port. Nothing appears if no connector is connected.) 5. The squares at the right side of the test display are for checking the controls. Press each key and the arrows on the Cursor Pad one by one. A control’s corresponding on-screen square “lights” in black if the control is normal. 6. Page 30 4. INSTALLATION Mounting on the bulkhead, Flush mounting in a panel 4.1 Display Unit Mounting considerations See the instructions on the bulkhead or flush mounting template (supplied). The display unit can be installed on a desktop, on the bulkhead or flush mounted in a panel. Page 31 submerged, even when the boat is rolling, pitching or up on a plane at high speed. For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. Page 32 Hole for stuffing tube DO NOT paint the transducer. Do not use this method on an inboard motor boat because turbulence is created by the propeller ahead of the transducer. Lower Half Saw along slope of hull. This may require a certain amount of experimentation for fine tuning at high cruising speeds. 5 x 20 5 x 20 4. Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces. M5 x 14 No. 2 5 x 20 5 x 20 Transom mount transducer, mounted projecting from hull No.

The more detail you provide for your issue and question, the easier it will be for other Furuno LS-4100 owners to properly answer your question. Ask a question About the Furuno LS-4100 This manual comes under the category Not categorized and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Furuno LS-4100 or do you need help. Ask your question here Furuno LS-4100 specifications ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free. ManualSearcher. com If you continue to use this site we will assume that you are happy with it. Read more Ok. Discover everything Scribd has to offer, including books and audiobooks from major publishers. Start Free Trial Cancel anytime.Browse Books Site Directory Site Language: English Change Language English Change Language. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction. Therefore, in an instruction of Furuno Ls4100 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities.

A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Furuno Ls4100, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Furuno service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Furuno Ls4100. After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid. It features a waterproof 5? high-definition silver bright LCD screen that offers a remarkably detailed picture of fish and bottom structure. With a resolution of 240 (H) x 320 (V) pixels, it has the highest resolution in its class. The LS4100 offers dual frequency capabilities, both 50 and 200 kHz, and has an outstanding 300 W RMS (2,400 Watt peak-to-peak) output power, making this fish finder the leader in its class. Choose from a variety of operating modes, including manual or two auto modes, fishing or cruising. The cruising mode uses a higher clutter refection setting than the fishing mode, making it useful to track the bottom while cruising. The LS4100 will redraw the entire echogram so that the contour can be shown seamlessly. Any waypoint can be selected as a destination Specifications. Adjusts gain. Selects basic display range. The auto mode in use is shown as (Auto-Fishing) or (Auto-Cruising) at the top left corne r on the screen.

Note: W hen in the auto mode, SHIFT and CLUTTER cannot be adjusted manually. Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Flange Nut Coat with silicone sealant. T ape connectors with vulcaninzing tape and then vinyl tape to waterproof them. Note: WAAS is cur rently in the development al phase. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share. Note that email addresses and full names are not considered private information. Please mention this; Therefore, avoid filling in personal details. The manual is 1,34 mb in size. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive. Check your email Please enter your email address. Momentary press: A djusts display contrast and brilliance. Ho wever, the equipment may not work properly. Contact y our dealer.) Y ou may press any key af ter the completion of the equipment check to start ope ration sooner. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd. E-mailadressen en volledige namen worden niet als privegegevens beschouwd. Wij vragen u dus ook te reageren op een antwoord. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien. De handleiding is 1,34 mb groot. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email.

Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider. Controleer uw email Vul dan hier uw emailadres in. To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. See All Buying Options Add to Wish List Disabling it will result in some disabled or missing features. You can still see all customer reviews for the product. The transducer instructions were pretty good for how to install it. It is more sensitive than the humminbird. I put the humminbird in the front of my boat for when im bass fishing from up there. I put both of them on to compare. I did not like however that I could not get and adapter to put my humminbird speed sensor on the furuno, which the customer service agent pointed out. I'm still curious if i could splice a 4 pin furuno to the humminbird and make it work The customer service was actually really good Overall this was a good purchase for me Reviewed in the United States on June 6, 2011 Hello, I get wrong depth readings with the Furuno LS4100 Echo Sounder when in shallow water. This is water less than 5 feet in depth. This applies to both fresh water and salt water. This is especially so in silty salt water. I boat mainly at the mouth on the Chesapeake Bay along the Chesapeake Bay Bridge Tunnel and the Eastern Shore Barrier Islands of VA. At some locations, I'm in 40-60 feet of water. In other locations, I'm frequently in ocean shoal areas with ocean swells breaking. I also get wrong depth readings at various boat ramp sites (both fresh and salt waters). The readings frequently bounce around with readings that are too high, sometimes double the value. I've experimented with changing the GAIN setting, and this fails to give better readings.

A reputable electronics department in the Richmond VA area tells me that this device is too powerful for the type of boating that I do. Well, such boating still requires reliable readings when passing thru dangerous ocean inlets. I have no faith in this Furuno product, and do not recommend it. Robert. Please try again later. From the United StatesThis unit does not. I could see the depth changes accurately out in 100' of water even when muddy at cruising speed. The transducer instructions were pretty good for how to install it. I'm still curious if i could splice a 4 pin furuno to the humminbird and make it work The customer service was actually really good Overall this was a good purchase for mePlease try again later. Please try again later. CHRISTIE L EASTER 5.0 out of 5 stars Please try again later. Please try again later.Please try again later. Please try again later.This is water less than 5 feet in depth. I have no faith in this Furuno product, and do not recommend it. Robert.Please try again later. Please try again later.Took me a few hours to install the unit and transom mount transducer. No real surprises, quite simple in fact. By far the most trouble free unit I have ever installed. Set it up per the directions and it is by far the best functioning unit I have ever used. Keeps the bottom constantly, regardless of speed and water conditions and has a very intuitive display and menu layout. Way better than all of the Humminbird and Lowrance models I have used in the passed, which included the Lowrance LCX-104 and 11x models. I would buy another one in an instant over a more expensive combo model.Please try again later. Please try again later.Please try again later. Please try again later.

furuno loud hailer manual

One 3-second blast, followed by one 2-second interval, one 1-second blast, one 2-second interval and one 1-second blast. Repeated every 120 seconds. TOW: Warning signal for vessels under tow. One 3-second blast, followed by one 2-second interval, one 1-second blast, one 2-second interval, one 1-second blast, one 2-second interval, and one 1-second blast. A rapidly ringing bell tone sounds for a duration of 5 seconds, repeated at an interval of 60 seconds. AGND: Warning signal for vessels aground. Two bell tones of 0.5 seconds, a bell tone of 1 second followed by a rapidly ringing bell tone for a duration of 5 seconds, followed by a bell tone of 2 seconds and 0.5 seconds. The signal from the external AF source (radio, CD player, etc.) sounds from all intercom stations and any connected horn speakers. Both horn speakers are selected automatically when the alarm mode is enabled. If the alarm is triggered, the volume output is automatically set to maximum. An attempt is made to remove the Loud Hailer with alarm mode active ALL, FWD, AFT and BOTH indicators light. YELP indicator goes off. ALL, FWD, AFT and BOTH indicators go off. This chapter contains maintenance and troubleshooting instructions to be followed to obtain optimum performance and the longest possible life of the equipment. 3.1 Preventive Maintenance General checks Check the following monthly. Check all cabling. If the power cannot be turned on, the fuse may have blown. Have a qualified technician check the fuse. Use the proper fuse. To see if your product has a battery, see the chap- ter on Maintenance. Follow the instructions below if a battery is used.Loud Hailer 0.45 m 0.30 m LH-5000 Intercom Speaker 2.25 m 1.50 m ISP-5000. Fix the hanger with four screws. Step 2 Set the loud hailer to the hanger. Pry off the frame from the front panel. Place the LH-5000 Loud Hailer in the hole and fix it with four Step 5 screws. Attach the microphone to the front microphone connector on the loud Step 6 hailer.

• furuno loud hailer lh3000 manual, furuno loud hailer manual, furuno loud hailer manual download, furuno loud hailer manual pdf, furuno loud hailer manual instructions, furuno loud hailer manual free.

Contact a FURUNO agent for service. Make sure no rain or water splash leaks into the equipment. Fire or electrical shock can result if water leaks in the equipment. We are confident you will see why FURUNO has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. Refer to the mounting template (supplied) for installation instructions. Mounting considerations When planning the location for the Loud Hailer, keep in the mind the following considerations. Name Type Flush Mounting Plate TZ7300012A Screw 6X12 SUS304 Wing Screw M4X35 SUS304 Wing Nut M4 SUS304 1. Make a cutout in the mounting location referring to flush mount outline drawing. 2. For mounting dimensions and fixing instructions, see the outline drawing. Intercom speaker. See the illustration on the next page for how to connect equipment to terminals. Refer to the interconnection diagram for detailed information. Rear panel layout. Other equipment are connected similarly. (4) Set terminal; TERMINAL ARRANGEMENT 13.6V CAL3 LH-3000, rear panel, how to wire terminals Jeweler’s tighten screws.They should also be pointed in the opposite direction of the microphone as you are speaking into it. Before mounting any horn, you should test it with the HAIL feature with the horn in the desired location to check for suitability of mounting location. What this means is that the heat sink ground is floating and will not ground batteries if they are connected to the ship’s chassis. To maintain a floating ground: 1. Use a stereo plug when connecting a 4 ohm speaker to the external speaker plug. Chooses which intercom station (IC1, IC2, IC3, IC4) to call. Chooses warning signal among YELP, UNWY, SAIL and TOW. The equipment is in the standby mode when the “ALL”. The two manual signals, YELP and MAN, are designed to be sounded at each press of the PTT switch on the microphone.

If an alarm is triggered, the LH-5000 sounds the alert for two minutes and stop for five minutes in cycle. Countdown will start. Then it sounds alarm tone loudly for two minutes, and then pauses for five minutes. To interrupt the warning signal, press and hold the PTT key on the microphone and speak into it. Press the PTT key on the microphone and speak into it. Step 2 Release the PTT key to receive. INTERNAL: uses the built-in speaker. Step 3 All your customized settings such as key backlighting are restored to factory settings. The table below lists the factory setting. Function Default Setting DIMMER Level 3 CONTRAST Level 3. Replacing the Fuse If the LH-5000 cannot be powered on, the 15 A fuse inside the power cord may be blown. In this case, only the qualified technician is allowed to check and. Do not use the equipment for other thanFOREWORD. iii. SYSTEM CONFIGURATION. iv. EQUIPMENT LIST. ivA Word to the Owner of the LH-3000. Congratulations on your choice of the FURUNO LH-3000 Loud Hailer. We. Page 6: EQUIPMENT LIST SYSTEM CONFIGURATIONThe Loud Hailer can be mounted on a desktop, on the overhead, on. Page 8 1. INSTALLATION. Flush mounting. Requires flush mount kit LH-3020 (Code No. 000-149-112). See the flush mount outlineFour intercom speakers (maximum) may be connected to get 2-way communicationsAll equipment are terminated at the rear panel of the LH-3000. See the illustration on the. Page 11 1. INSTALLATION. Wiring. The illustration below shows how to connect the power supply. Other equipment arePower connection 77 3. The LH-3000 is intended forHailer horn (local supply). Mount the hailer horns (local supply) facing away from the Loud Hailer to. Page 14 1. INSTALLATION. Floating ground. The LH-3000 has a floating ground. What this means is that the heat sink ground is. Page 15: 2. OPERATIONAL OVERVIEW 2. OPERATIONAL OVERVIEWManually selecting a calling stationYour Loud Hailer has eight different warning signals: two manual and six automatic. The.

Installing the Microphone Determine a location where it is easy to install hanger. Step 1 Fix the hanger with three screws. Step 2 Place the microphone into the hanger. Fix the hanger with four screws. Step 2 Set the intercom speaker to the hanger. Pry off the frame from the front panel. Step 2 Paste the cushion on the back of the front panel by the double-side Step 3 tape on the cushion. Step 1 The diameter of the hole ranges from 20 mm to 25 mm. Step 2 Place the seal, cable holder, and waterproof cover sequentially around Step 3 the extension cable. Fasten the nut. Step 4 Fasten the three screws. Step 5 Put the cover on the extension cable and tighten it. Move the heat shrink tubes to the soldered correction, and then apply Step 3 heat to the tubes. Step 1 Connect one end of the extension cable to the connector on the unit Step 2 and tighten it. Step 3 Connect the microphone to the connector of extension cable. Step 4 1.5.4 Connecting the Ground Cable Loosen the screw on the rear back of the unit. Step 2 Tighten the screw again. Step 3. Step 4 If you do not adjust the brightness within 60 seconds, the LH-5000 returns to the previous mode automatically. Adjusting the Contrast Press the MENU key on the front panel. To adjust the volume from the intercom or horn speaker, rotate the Hailer Volume Control key. Calling All Speakers All speakers include all the six intercom speakers and both horn speakers. Press the ALL key on the front panel. Press and hold the PTT key on the microphone and speak into the Step 2 microphone. The following information appears on the screen. To rename the name, see 2.16 Renaming the Intercom Station. Press and hold the PTT key on the microphone and speak into the Step 2 microphone. The manual and yelp signals are sounded when you press and hold the PTT key on the microphone. Automatically Sending a warning signal Press the FOG key on the front panel.When the alarm mode is enabled, both horn speakers are automatically selected.

) to the intercom speakers and external horns. Only qualified personnel should work inside the equipment. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. CAUTION Do not use the equipment for other than its intended purpose. Use of the equipment for other than its intended purpose may result in damage to the equipment or cause bodlily injury. Page 4 TABLE OF CONTENTS FOREWORD.Page 5 FOREWORD A Word to the Owner of the LH-3000 Congratulations on your choice of the FURUNO LH-3000 Loud Hailer. We are confident you will see why FURUNO has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers. Refer to the mounting template (supplied) for installation instructions. Contents of flush mount kit 1. 2. 3. 4. 5. Name Type Code No. Flush Mounting Plate TZ7300012A 999-999-025 2 Screw Wing Screw 6X12 SUS304 M4X35 SUS304 999-999-027 999-999-027 2 4 Wing Nut M4 SUS304 999-999-028 4 Make a cutout in the mounting location referring to flush mount outline drawing. Place the Loud Hailer in the cutout. Page 9 1. INSTALLATION 1.2 Intercom Speaker (option) Four intercom speakers (maximum) may be connected to get 2-way communications between master station and one or all intercom speakers. For mounting dimensions and fixing instructions, see the outline drawing. Page 10 1. INSTALLATION 1.3 Wiring All equipment are terminated at the rear panel of the LH-3000. See the illustration on the next page for how to connect equipment to terminals. Rear panel layout 13. Page 11 1. INSTALLATION Wiring The illustration below shows how to connect the power supply. Other equipment are connected similarly. (1) Unfasten screws. They should also be pointed in the opposite direction of the microphone as you are speaking into it.

Page 21 2. OPERATION. SAIL: Warning signal for sailboats, tug boats and tow boats underway. One 3-secondANCH: Warning signal for vessels at anchor. A rapidly ringing bell tone sounds for aSounding an automatic warning signalTransmitting the auxiliary signal over all speakers. An audio signal from an external. Page 25 2. OPERATIONThe LH-3000 can operate as a burglar alarm by connecting an external, normal-open switch. Page 26 2. OPERATIONPeriodic checks and maintenance are important for maintaining performance. This chapterThe 6A fuse inside the Loud Hailer protects it from reverse polarity and. Page 29: SPECIFICATIONS FURUNO LH-3000Y. HataiY. HataiY. Hatai. You can now coordinate any action even on a big ship or facility. You can hail and communicate with intercoms as well. With 8 warning signals, including fog horn, vessels around will be notified of your presence and it will prevent own ship from collisions. This allows you to customize the channel's name so you know who your are talking to. It can also be used as a burglar alarm. Prices are valid in US and Canada only. The LH3000 is designed for a wide variety of ships, requiring high quality onboard and ship-to-ship communications under almost all circumstances. Solidly built and waterproof, the LH3000 contains a high quality built-in speaker and a microphone. On its front panel, there are easy-to-see states indicators. By generating voice or eight internationally acknowledged warning signals from the horns, the LH3000 notifies nearby vessels of your presence and status regardless of visibility conditions. It can function as an intercom, when connected to optional speakers. Up to four intercoms can be connected for two-way communication between the bridge and one or all intercom stations. When connected to an external alarm unit, the LH3000 can function as a security alarm. An auxiliary audio input allows transmission of music or other external audio signals (from CD player, radio, etc.

NMEA2000 to any NavNet TZtouch2 MFD, DSC calling can be initiated directly from Back Features Loud Hailer, Fog Horn and Warning Signal features are Additionally, the horn speaker can be used to collect external sounds and In this way, a person on the deck can easily communicate with the bridge, a Listen Back function can also be an effective tool on sport fishing vessels, Any products can be Otherwise and come with Full Manufacturer's Warranty Marine Electronics Store. A high performance, full featured system this unit incudes 2 hailers and 6 intercoms for a total of 8 channels. Includes Siren mode, Listen Back, alarm functions and more! Quickly draw attention to your vessel through voice or via any of the 8 internationally recognized warning signals from the horns on the vessel. Regardless of limited visibility while on the water due to fog or while traveling at night, you can utilize up to 6 horn speakers with this one device, outputting power of 30 watts per speaker ensuring you are heard by anyone close by. Another great “safety” feature of the LH-5000 is the Siren Mode and Alarm mode that can alert you to a fire or theft when connected to the boats alarm or fire alert system. The Listen Back feature is important and allows sounds to be amplified through the built-in speaker allowing you to hear your crew whether they are on the dock, your boat deck, or anywhere else on or off the vessel through the two-way intercom speakers. Personalize the Furuno LH-5000 with customizable names of channels so you know specifically who you are speaking to on the vessel as well. For a low cost communication device for your helm, the Furuno LH-5000 Loud Hailer is the preferred choice. Quickly draw attention to your vessel through voice or via any of the 8 internationally recognized warning signals from the horns on the vessel.

Regardless of limited visibility while on the water due to fog or while traveling at night, you can utilize up to 6 horn speakers with this one device, outputting power of 30 watts per speaker ensuring you are heard by anyone close by. For a low cost communication device for your helm, the Furuno LH-5000 Loud Hailer is the preferred choice. However, our customer showroom is currently closed. We thank you for your patience as we help you access the new site!This is a screenshot of it.I need to know which wire goes on which specific male pin on the plug.Use of this site indicates your consent to the Terms of Use. Page Count: 3 The illustration below shows how to connect the power supply. Other equipment areSheath. ArmorDrain wire fabricationArmorUse cable type DPYC-1.5 or. Conductor. CutSolder drain wire. DPYC-1.5 Sectional viewIf the power leads areIntercom speaker (option). Up to four intercom speakers may be connected to the intercom speaker terminals labeled. CAL1-CAL4. Connect each speaker to the terminal block according to desired intercomHowever, to meet EMC requirements theIn this case, the length of the cable between the junction box and anIntercom. Speaker. Distance between loud hailer and intercom speaker is less than 2 m. Loud HailerIntercom. Junction. Box. Distance between loud hailer and intercom speaker is 2-20 m. Loud HailerRemove the outer sheath andInner sheathTwist and trim the shield. Cut the unused cores. Solder a vinyl wire to the shield. Tape the sheath. VinylVinyl wire. Fabrication of speaker cableDISTANCE BETWEEN JB AND LH-3010 SHALL BE 1m OR LESS.JB?LH-3010??1m????????YoshHataiHataiHatai,File Type Extension: pdf. PDF Version: 1.5. Linearized: No. Modify Date: 2004:08:02 14:19:47-07:00. Create Date: 2004:07:27 13:24:58-07:00. Producer: Acrobat Distiller 4.05 for Windows. Page Count: 3. Has XFA: No. About: uuid:08428753-d86c-457d-badd-699e6869f886. Mod Date: 2004:08:02 14:19:47-07:00. Creation Date: 2004:07:27 13:24:58-07:00.

Before mounting any horn, you should test it with the HAIL feature with the horn in the desired location to check for suitability of mounting location. Connect horns to the Loud Hailer with cable type DPYC-1.5 or equivalent. (See page 6 for how to fabricate this cable. Page 14 1. INSTALLATION Floating ground The LH-3000 has a floating ground. What this means is that the heat sink ground is floating and will not ground batteries if they are connected to the ship’s chassis. To maintain a floating ground: 1. Use a stereo plug when connecting a 4 ohm speaker to the external speaker plug. Connect it as shown in the illustration below. After a one-second delay, a short tone sounds from the selected intercom station. 2. Press the PTT switch on the microphone and speak into the microphone. 3. Release the PTT switch to listen for a reply from the selected intercom station. The two manual signals, YELP and MAN, are designed to be sounded at each press of the PTT switch on the microphone. Only the horn speakers sound warning signals and the volume is automatically set to maximum when sounding warning signals. Page 21 2. OPERATION SAIL: Warning signal for sailboats, tug boats and tow boats underway. One 3-second blast, followed by one 2-second interval, one 1-second blast, one 2-second interval and one 1-second blast. Repeated every 120 seconds. 1s 2s 1s 2s 3s 120 s Sailing signal TOW: Warning signal for vessels under tow. One 3-second blast, followed by one 2-second interval, one 1-second blast, one 2-second interval, one 1-second blast, one 2-second interval, and one 1-second blast. Repeated every 120 seconds. Page 22 2. OPERATION ANCH: Warning signal for vessels at anchor. A rapidly ringing bell tone sounds for a duration of 5 seconds, repeated at an interval of 60 seconds. 5s 60 s Anchor signal AGND: Warning signal for vessels aground. The signal from the external AF source (radio, CD player, etc.) sounds from all intercom stations and any connected horn speakers.

Adjust the output volume level directly from the external input source. 2. Page 25 2. OPERATION 2.12 Alarm Mode The LH-3000 can operate as a burglar alarm by connecting an external, normal-open switch to the ALRM terminals on the rear panel. Both horn speakers are selected automatically when the alarm mode is enabled. If the alarm is triggered, the volume output is automatically set to maximum. After 5 minutes ALL, FWD, AFT and BOTH indicators go off. BOTH indicator lights every four seconds. STANDBY STATUS (Alarm mode enabled) An attempt is made to remove the Loud Hailer with alarm mode active Alarm sound is released through both horn speakers at maximum volume. Page 27 3. MAINTENANCE, TROUBLESHOOTING Periodic checks and maintenance are important for maintaining performance. This chapter contains maintenance and troubleshooting instructions to be followed to obtain optimum performance and the longest possible life of the equipment. WARNING Do not open the equipment. If the power cannot be turned on, the fuse may have blown. WARNING Use the proper fuse. Use of a wrong fuse can result in damage to the equipment or cause fire. 3.3 Troubleshooting Below are simple troubleshooting procedures which the user may follow to try to restore normal operation. DISTANCE BETWEEN LH-3000 AND JB SHALL BE 20m OR LESS. DISTANCE BETWEEN JB AND LH-3010 SHALL BE 1m OR LESS. Printed in Japan PUB.No. OME-56460 ( DAMI ) LH-3000 FIRST EDITION: FEB. Warranty. Simplified Loud Hailer DSC, AIS Receiver, and Simplified Loud Hailer with intercom. Its compact housing When connected via.

Metadata Date: 2004:08:02 14:19:47-07:00. Document ID: uuid:92e3effa-5133-403a-bd1f-063d4a7740bc. Warning, Caution. Prohibitive ActionThis equipment uses high voltageOnly qualifiedIf water leaks into the equipment orMandatory ActionFire, electrical shock or serious injuryMake sure no rain or water splashFire or electrical shock can result if waterFire or electrical shock can result. If the equipment is giving off smokeDo not place liquid-filled containersFire or electrical shock can result if aFire or electrical shock can result. If you feel the equipment is actingDo not operate the equipment withElectrical shock can result. Use the correct fuse. Use of the wrong fuse can cause fire orElectrical shock can result.The equipment uses high voltage thatTurn off the power at the mainsElectrical shock, serious injury or fireDo not approach the antenna closerThe antenna emits radio waves that canRF power density. Distance DescriptionMaximum Antenna Gain: 6 dBi. This device complies with part 15 ofOperation is subject to the followingThis equipment complies with FCCThis equipment complies with FCCThis antenna should be installed withThis transmitter must not be co-locatedNote: This equipment has been testedThese limits are designed to provideThis equipment generates uses and canHowever, there is no guarantee thatIf this equipment does cause harmfulISEDC RSS warning. This device complies with Innovation. Science and Economic Development. Canada Compliance RSS standardLe present appareil est conforme aux. CNR d'Innovation, Sciences et Developpement economique CanadaL'exploitation est autorisee aux deuxThis equipment complies with ISEDC. RF radiation exposure limits set forth forThe antenna should be installed withThis transmitter must not be co-locatedISEDC exposition aux radiations. Cet equipement est conforme avec. ISEDC les limites d'exposition auxL'antenne doit etre installee avec uneCet emetteur ne doit pas etreAny Changes or modifications notCE Compliance Statement.

This product complies with CE under. The maximum antenna gain is 6dBi,Connection to the wrong power supplyObserve the following safe compassSteeringCalls. 39FURUNO Electric Company thanks you for purchasing the FM-4800 Marine VHF. Radiotelephone. We are confident you will discover why the FURUNO name hasSince 1948, FURUNO has enjoyed an enviable reputation for quality and reliabilityThis dedication to excellence is furthered by our extensiveYour equipment is designed and constructed to meet the rigorous demands of thePlease carefully read and follow the operation,We would appreciate feedback from you, the end-user, about whether we areThank you for considering and purchasing FURUNO. Features. FURUNO FM-4800 Marine VHF Radiotelephone supports the following features:Class D DSC with Distress, Individual and All Ship calls. Built-in AIS receiver. Built-in high-sensitivity GNSS receiver. Dual station with optional handset HS-4800. ATIS mode available for inland waterway in Europe. Pre-programmed frequency band for USA, Canadian and International marineInitiate DSC call directly from NavNet TZtouch2 series when connectedFully-waterproofed transceiver, microphone and handset (IP67)Speaker. Horn. SpeakerOptional Supply. Local SupplyCH16 is known as the Hail and Distress Channel. When an emergency occurs, beThen do as follows. Step 1. Press the Push-To-Talk (PTT) key of the microphone or handset and sayStep 2. Step 3Step 4. Report the nature of your distress (sinking, collision, aground, fire, piracy,Step 5. State the kind of assistance you desire (pumps, medical aid, etc.). Step 6. Report the number of persons aboard and condition of them. Step 7. Estimate the present seaworthiness and condition of your vessel. Step 8. Give your vessel's description: length, design (power or sail), color andStep 9. Release the PTT switch and listen. Step 10. Optional: If there is no answer, repeat the above procedure.

If there is stillNoteFor more information, seeCH16 (or CH9, depending on area) should be used as the calling channel for initialHowever, its primary purpose is for emergencyCH16 or CH9 is monitored by other vessels and Coast Guard stations in allThe use of CH16 or CH9 should be limited to making initial contact only. A callBefore contact another vessel, refer to the channel charts in the Appendix and selectMonitor the proposedWhen the other vessel. Then switch to the new channel. When theWhen all communication with the vessel is completed, end the last transmission by. Note that you do not need to state your callRemember to return to CH16 when not using another channel. Some radiosChannel 13 is used at docks and bridges and by vessels maneuvering in port. Messages on this channel must concern navigation only, such as meeting andChannel 67 is used for navigational traffic between vessels. By regulation, power is normally limited to 1 Watt on these channels. Your radio isSee section 2. CONTROLS for how to temporarily override the low-power limit on these twoNo. DescriptionDescriptionPress the key to cancel all other modes and to tune into the priority channelsNote. CH9 is used in some parts of the world as an alternative hailing channel toDescription. Press and hold the key in radio mode to enable the radio for voiceNote. When the PTT key on the microphone is pressed continuously, transmissionThis limits unintentional transmissions due to aIn addition, Power is automatically reduced to protect against overheatingChanges the channel up or down. Press the switch to toggle between 25 W (High) and 1 W (Low). Press the key to cancel all other modes and to tune into the priority channelsNote. CH9 is used in some parts of the world as an alternative calling channel toNo. Description. The transmitter is enabled for voice communications with anotherNote.

When the PTT key on the microphone is pressed continuously,This limits unintentionalIn addition, Power is automatically reduced to protect againstDescription. Press the key to switch between the volume adjust screen and thePress the switch to toggle between 25 W (High) and 1 W (Low).Press the key to cancel all other modes and to tune into the priorityPress the key again to return to theNote. CH9 is used in some parts of the world as an alternative callingPress the key to turn the handset on or off.DescriptionThis icon disappears if there is no GNSS data. This icon flashes with 500ms when there is GNSS data before, butThis icon disappears if user selects END of AUTO POSOperational Status iconDescription. Display location information including longitude, latitude, time, COG,NoteNMEA0183. The last two are external sensors. Their priorities inIn non scan mode: display CH NAME. In scan mode. SCAN ALL: indicates that the user selects SCAN ALL. MEMORY SCAN: indicates that the user selects MEMORY SCAN. Displays the current channel number. Note: the channel number 12 is not displayed.WEATHER MODE is ON.Digital Selective Calling (DSC) is a semi-automated method to establish a radio call. DSC has been designated by the International Maritime Organization (IMO) as anIt has also beenDSC replaces listening watches on distress frequencies and is used to broadcastThis system allows mariners to instantly transmit a distress call with GNSS positionDSC radio.An MMSI is a nine-digit number used on marine radios capable of using DSC. ThisNote. To use the DSC functions, this vessel’s MMSI must be entered into the radio.Caution. An MMSI can be entered only once. Therefore, be careful not to enter the wrong. MMSI number. If you need to change the MMSI number after it has been entered,Step 1. Step 2. Step 3. Enter you MMSI number (nine digits). If you enter a wrong digit, press the BACK key until the wrong digit isStep 4Step 5FM-4800 can send and receive DSC distress calls.

When FM-4800 receives GNSSNote. To transmit a DSC distress call, this vessel’s MMSI number must be entered intoInitiate a DSC distress call without specifying the nature ofThe FM-4800 can transmit a DSC distress call without specifying the followingListing, Sinking, Adrift, Abandoning, Piracy, and MOB (Man Overboard). Press and hold the Distress key (about 4 seconds). The unit beeps andAfter the distress signal is sent, the radio waits for an acknowledgement with the. If no acknowledgement is received, the distress signal is repeated atStep 3Step 4. Press and hold the PTT key to announce your situation on CH16. Initiate a DSC distress call with the nature of distress specified. The FM-4800 is capable of transmitting a DSC distress call with the followingSinking, Adrift, Abandoning, Piracy, and MOB (Man Overboard). Short-press the Distress key. Step 4. Select the nature of the distress. Step 5. The unit beeps andStep 6. After the distress signal is sent, the radio waits for an acknowledgement with the. If no acknowledgement is received, the distress signal is repeated atStep 7. Press and hold the PTT key to announce your situation on CH16.If no position data is available at the time of distress, you can enter the latitude andStep 1. Step 4Step 5. The unit beeps andAfter the distress signal is sent, the radio waits for an. If no acknowledgement is received, the distress signal is repeated atStep 6. Pause a DSC distress call. After a DSC distress call is sent, the DSC distress call is repeated atThe FM-4800 has aTo pause the distress call. Restart the DSC distress call. At this time, you can. Sending a distress cancel call. When the emergency is released, you can cancel the distress call. Step 1Step 3. Press and hold the PTT key to announce your situation.Step 1. When a DSC distress call is received, the emergency alarm sounds. Optional: The display shows the MMSI of the vessel in distress. To show. The radio switches to CH16 automatically. Note.

furuno ls 4100 manuale

WATER TYPE: Choose the water type with which to use the LS-4100, from Salt or Fresh. KEY BEEP: Turn key beep on or off. BATT VOLTAGE: Turn the battery voltage indication (appears at the top right corner on the screen) on or off. Page 3 BASIC RANGE 1 - BASIC RANGE 8: Set range of each of the eight basic. Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Checking the items listed in the table below monthly will help keep your equipment in good shape for years to come. For any NG, request service. (A special connector is required to test the NMEA port. Nothing appears if no connector is connected.) 5. When choosing a location keep the following in mind: Keep the display unit out of direct sunlight. For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. This may require a certain amount of experimentation for fine tuning at high cruising speeds. 4. Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces. Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of the boat. Mark this mounting hole. 5. If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover. Position the cover over the cable where it enters the hull. Refer to the interconnection diagram to connect cables. Leave slack in cables to facilitate checking and maintenance. The transmission speed for both input and output is 4800 bps. Data is output at two-second intervals. Input data sentences. Off: Outputs the data sentences of LS-4100 only. On: Outputs the data sentences of LS-4100 and sentences which are input from other equipment. 6. To restore normal operation, turn off the power and then turn it on again.

• furuno ls 4100 manuale italiano, furuno ls 4100 manual, furuno ls 4100 manual pdf, furuno ls 4100 user manual, furuno ls 4100 manuale.

Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer. WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. FURUNO will assume no responsibility for any damage associated with improper installation. Use the specified power cable. The main features of the LS-4100 are Bright 5-inch monochrome LCD gives excellent readability even in broad daylight. Automatic function permits unattended adjustment of range and gain. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation and displays program number. The time remaining until power is turned off is counted down on the screen. The lower the frequency of the signal, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. 200 kHz The higher the frequency of the ultrasonic signal the better the. This mode is useful for determining bottom contour. When the bottom depth increases, the display shift to keep the bottom echo at the lower part of the screen. Page 1 or Page 2 of the main menu appears depending on the page last used. The auto mode in use is shown as (Auto-Fishing) or (Auto-Cruising) at the top left corner on the screen. Note: When in the auto mode, SHIFT and CLUTTER cannot be adjusted manually. Shifting the range The basic range may be shifted up or down in the manual mode as follows: Window can be shifted up and down to select the depth. Display Range and display shift concept 1. Depth, temperature, speed setting window 10.When TLL or FURUNO-TLL is selected at TLL OUTPUT on the System menu, the latitude and longitude position at the cursor is output to the navigator. GPS 2D: 2D (dimension) GPS position fix GPS 3D: 3D GPS fix GPS W2D: 2D WAAS position fix. Fish school clearly shown White line 52.6 52.6 White Line OFF White Line ON (Mesh) How white line works. SYSTEM MENU LANGUAGE English DEPTH UNIT: ft.

Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Furuno LS-4100 owners to properly answer your question. Ask a question About the Furuno LS-4100 This manual comes under the category Not categorized and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Furuno LS-4100 or do you need help. Ask your question here Furuno LS-4100 specifications ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free. ManualSearcher. com If you continue to use this site we will assume that you are happy with it. Read more Ok. There are no uer-serviceable parts The transducer may be damaged. inside. The picture is not refreshed when Do not disassemble or modify the picture advancement is stopped. equipment. Maneuvering the vessel in this condition Fire, electrical shock or serious injury may result in a dangerous situation. can result. Use the proper gain seFire or electrical shock can result if the Performance will be affected.Water leakage can sink the vesselFURUNO LS-4100 5? Echo Sounder. Comprised of a display unit and a We are confident you will see why the transducer, the LS-4100 displays FURUNO name has become underwater conditions on a bright 5-inch synonymous with quality and reliability.Qty Remarks Display Unit LS-4100 ? 1 520-5PSD 000-Selects display mode. GAIN Adjusts gain. RANGE Selects basic display range. Momentary press: Adjusts display contrast and brilliance.

Note: WAAS is currently in the developmental phase. During the developmental phase the reliability and availability of the WAAS signal cannot be guaranteed. Therefore, any position data should be verified against other sources to confirm reliability. All rights reserved. Do no turn on the. Page 4 Safety Instructions for the InstallerPage 5: FOREWORD FOREWORD. A Word to LS-4100 Features. Owners The FURUNO LS-4100 is a dual. Congratulations on your choice of the frequency. Page 6: SYSTEM OVERVIEW SYSTEM OVERVIEW. System configurationPage 10 Bottom-zoom display Nav data displays. This mode expands bottom and bottom The nav data displays appear on the leftThe LS-4100 has three menus: Main. System and Installation.The auto mode in. Page 13 1000ft Adjusting the gainThe VRM (Variable Range Marker)Interference from other acoustic Low intensity “speckles” may appearSediment in the water or reflections transmission. Page 17 1.14 Alarms MENU from page 2 on the menu.Page 22 DIGITAL DISPLAYSThe System menu mainly consists of 2.1 System MenuPage 26 SPEED CALIB.: If the speedMarine life on the transducer. Page 28 3.6 Troubleshooting 3.7 Diagnostics. The table below provides basic If you feel your unit is not workingMounting considerationsPage 31 submerged, even when the boat is Typical thru-hull mountPage 32 Hole for BOW DO NOT paint the transducer.Screwdrivers. Straight edgeThe installation menu mainly contains (NMEA PORT, NMEA MIX)Page 43 GPS WAAS: Chooses how to use the BOTTOM LEVEL: If the depth. WAAS signal when connecting with a indication is. Page 44: SPECIFICATIONS SPECIFICATIONS OF ECHO SOUNDER LS-4100. At InstructionsManuals.com we have gathered together the manuals to make it easier for you to locate them. We take no responsibility for the validity of the information available in each manual nor do we have any affiliation with the brands nor their products. (Sounders Furuno). Ask your question here.

A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Furuno Ls4100, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Furuno service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Furuno Ls4100. After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid. Do no turn on the equipment with the transducer out of water. There are no uer-serviceable parts inside. The transducer may be damaged. Do not disassemble or modify the equipment. The picture is not refreshed when picture advancement is stopped. Fire, electrical shock or serious injury can result. Maneuvering the vessel in this condition may result in a dangerous situation. Page 4 Safety Instructions for the Installer WARNING CAUTION Turn off the power at the switchboard before beginning the installation. Do not install the equipment where air bubbles and noise are present. Fire or electrical shock can result if the power is left on. Performance will be affected. The following are guidelines for handling of the transducer cable. Be sure no water leaks in at the transducer or sensor mounting location. - Do not locate near oils and fuels. - Locate it in a safe place.

Display unit How to remove This The sounder uses ultrasonic signals to display is useful for comparing the same detect bottom conditions. The lower the picture with two different transmitting frequency of the signal, the wider the frequencies.Data other than depth RANGE of the SYSTEM menu. This requires appropriate sensor.When the bottom depth You can display between two and four increases, the display shift to keep the items in a nav data display and choose bottom echo at the lower part of the the item and ordPage 1 or Page 2 of the menu, or press Shifting the range The basic range mayThis is mainly due electronic equipment on your boat may to sediment in the water or noise. These show itself on the display as shown in can be suppressed by adjusting the figure below. CLUTTER on the menu. When the To suppress interference, do the automatic mode is on, clutter is following: automatiWeak Note: In the dual frequency display, the echoes A-scope display is only available with the high frequency displ. Discover everything Scribd has to offer, including books and audiobooks from major publishers. Start Free Trial Cancel anytime.Browse Books Site Directory Site Language: English Change Language English Change Language. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction. Therefore, in an instruction of Furuno Ls4100 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities.

The squares at the right side of the test display are for checking the controls. Press each key and the arrows on the Cursor Pad one by one. A control’s corresponding on-screen square “lights” in black if the control is normal. 6. Page 30 4. INSTALLATION Mounting on the bulkhead, Flush mounting in a panel 4.1 Display Unit Mounting considerations See the instructions on the bulkhead or flush mounting template (supplied). The display unit can be installed on a desktop, on the bulkhead or flush mounted in a panel. Page 31 submerged, even when the boat is rolling, pitching or up on a plane at high speed. For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. Page 32 Hole for stuffing tube DO NOT paint the transducer. Do not use this method on an inboard motor boat because turbulence is created by the propeller ahead of the transducer. Lower Half Saw along slope of hull. This may require a certain amount of experimentation for fine tuning at high cruising speeds. 5 x 20 5 x 20 4. Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces. M5 x 14 No. 2 5 x 20 5 x 20 Transom mount transducer, mounted projecting from hull No. The procedure for this is shown later. Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of the boat. Fiberglass hull: Minimize surface cracking by chamfering the gelcoat. Note: Do not position the sensor farther into the water than necessary to avoid increasing drag, spray, and water noise and reducing boat speed. Tighten the screws. Attaching the sensor to the bracket 2. Insert the sensor’s pivot arms into the slots near the top of the bracket. 3. Page 39 4. Position the second cable clamp halfway between the first clamp and the cable hole. Mark this mounting hole. 5.

If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover. Position the cover over the cable where it enters the hull. The signal line ground is isolated from the chassis ground, however the power line is not insulated. Therefore, when connecting eternal equipment having positive ground, do not ground the signal line to the chassis. If excessive noise shows on the screen, the ground may be inadequate. Sentence MWV RMA Connect to XDR port at rear of display unit RMB MJ-A10SPF RMC MJ-A6SRMD MJ-A10SRMD VHW VTG Tape connectors with vulcaninzing tape and then vinyl tape to waterproof them. Bind tape ends with cable ties to prevent From tape from unraveling. Page 42 4.9 Installation Menu NMEA port setup (NMEA PORT, NMEA MIX) The installation menu mainly contains items which are set at installation. Page 43 BOTTOM LEVEL: If the depth indication is unstable in automatic operation, or the bottom echo cannot be displayed in the darkest gray tone by adjusting the gain controls in manual operation, you may adjust the bottom echo level detection circuit, for both 50 kHz and 200 kHz, to stabilize the indication. Generally, lower the bottom level for inner hull installation where the receive level is too low. Printed in Japan PUB.No. OME-23710 ( HIMA ) LS-4100 FIRST EDITION: MAR. Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire. Page 4 ii Safety Instructions for the Installer WARNING Turn off the power at the switchboard before beginning the installation. Be sure no water leaks in at the trans- ducer or sensor mounting location. Page 5 iii FOREWORD A W ord to LS-4100 Ow n er s Congratulations on your choice of the FURUNO LS-4100 5” Echo Sounder. We are confident y ou will see why the FURUNO name has become synonymous with quality and reliability. Adjusts gain. Selects basic display range. Momentary press: A djusts display contrast and brilliance.

Page 5 FOREWORD A Word to LS-4100 Owners Features The FURUNO LS-4100 is a dual frequency (50 kHz and 200 kHz) monochrome LCD echo sounder. Comprised of a display unit and a transducer, the LS-4100 displays underwater conditions on a bright 5-inch monochrome LCD. Congratulations on your choice of the FURUNO LS-4100 5” Echo Sounder. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. Page 6 SYSTEM OVERVIEW System configuration MODE MENU ESC DISPLAY UNIT LS-4100 GAIN RANGE MARK ECHO SOUNDER LS-4100 POWER BRILL Note: Contact your dealer for connection of other equipment. Page 7 1. OPERATION 1.1 Control Description Cursor Pad Selects menu items; shifts VRM. Selects display mode. GAIN Adjusts gain. Selects basic display range. Page 9 Single frequency display Dual frequency display 50 kHz The 50 kHz picture appears on the left; the 200 kHz picture on the right. This display is useful for comparing the same picture with two different transmitting frequencies. The sounder uses ultrasonic signals to detect bottom conditions. The lower the frequency of the signal, the wider the detection area. This mode is useful for determining bottom contour. When the bottom depth increases, the display shift to keep the bottom echo at the lower part of the screen. The nav data displays appear on the left of the screen. Data other than depth requires appropriate sensor. Page 11 1.5 Menu Operating Procedure Off Cruising Fishing The LS-4100 has three menus: Main, System and Installation. Page 1 or Page 2 of the main menu appears depending on the page last used.Generally, use a higher gain setting for greater depths and a lower setting for shallower waters. Use the proper gain setting. It is useful for estimating the kind of fish school and bottom composition. Sediment in the water or reflections from plankton may be painted on the display in low intensity tones.

Weak echoes Note: In the dual frequency display, the A-scope display is only available with the high frequency display. The cursor appears along with waypoint entry instructions. Page 25 BEARING: Ship’s course and bearing to a waypoint may be displayed in true or magnetic bearing. Magnetic bearing is true bearing plus (or minus) earth’s magnetic deviation. Requires bearing data. NAV DATA-1, -2: Choose the number of navigation data items to display on the nav data displays, from two, three or four items. Requires appropriate nav data. WATER TYPE: Choose the water type with which to use the LS-4100, from Salt or Fresh. Page 26 SPEED CALIB.: If the speed sensor-generated speed indication is wrong, you can correct it here, when “Own” is selected as speed source. Page 3 BASIC RANGE 1 - BASIC RANGE 8: Set range of each of the eight basic ranges. (Selectable range: 7 to 1500 ft) Note 1: All default basic ranges are restored whenever the depth unit is changed. Page 27 3. MAINTENANCE, TROUBLESHOOTING 3.3 Transducer Maintenance WARNING ELECTRICAL SHOCK HAZARD Marine life on the transducer face will result in a gradual decrease in sensitivity. Check the transducer face for cleanliness each time the boat is dry-docked. Carefully remove any marine life with a piece of wood or fine-grade sandpaper. Do not open the equipment. Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Page 28 3.6 Troubleshooting 3.7 Diagnostics The table below provides basic troubleshooting procedures which the user may follow to restore normal operation. If you feel your unit is not working properly, conduct the diagnostic test to find the problem. If you cannot restore normal operation, contact your dealer for advice. For any NG, request service. (A special connector is required to test the NMEA port. Nothing appears if no connector is connected.) 5.

Th e time remaining until power is turned of f is counted down on the screen. Page 9 3 Single fr equency displa y 50 kHz The sounder uses ultrasonic signals to detect bottom conditions. The refore, the 50 kHz frequency is useful for general detection and judging bottom condition. Page 10 4 Bottom-zoom displa y This mode exp ands bottom and bottom fish in the range width set with ZOOM RANGE of the SYSTEM menu. W hen the bot tom depth increases, the display shift to keep the bottom echo at the lower part of t he screen. Page 11 5 1.5 Menu Operating Procedure The LS-4100 has three menus: M ain, System and Installation. Page 1 or Page 2 of the main menu appears depending on the page last used. The auto mode in use is shown as (Auto-Fishing) or (Auto-Cruising) at the top left corne r on the screen. Note: W hen in the auto mode, SHIFT and CLUTTER cannot be adjusted manually. Range offset T o display the bottom t ail in detail in the automatic mode, offse t the range as below. Shif ting the range The basic range may be shif ted up or down in the manual mode as follows: Display Window can be shifted up and down to select the depth. Page 16 10 1.12 Erasing Weak Echoes Sediment in the water or reflections from plankton may be p ainted on the display in low intensity tones. Page 17 11 1.14 Alarms A l arm description The LS-4100 has six conditions which generate both audio and v isual alarms: bottom alarm, normal fish alarm, bottom lock fish alarm, water temperature alarm, arrival alarm and speed alarm. (The water temperature, arriv al and speed alarms require appropriate sensors. Page 24 18 2. SYSTEM MENU The System menu mainly consists of items which once set do not require frequent adjustment. Page 25 19 NA V DA T A -1, -2: Choose the number of navigation dat a items to display on the nav dat a displays, from two, three or four items. Requires appropriate nav data. W A TER TY PE: Choose the water type with which to use the LS-4100, from Salt or Fresh.

Page 26 20 SPEED C ALIB.: If the speed sensor-generated speed indication is wrong, you can correct it here, when “Own” is selected as speed source. Page 27 21 3. MAINTENANCE, TROUBLESHOOTING WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Checking the items listed in the table below monthly will help keep your equipment in good shape for years to come. Page 28 22 3.6 T roub leshooting The table below prov ides basic troubleshooting procedures which the user may follow to restore normal operation. Page 30 24 4. INST ALLA TION 4.1 Display Unit Mounting consi derati ons The display unit can be inst alled on a desktop, on the bulkhead or flush mounted in a panel. For planing hulls, a practical location is generally rather far as tern, so that the transducer is always in water regardless of the planing attitude. Page 32 26 BOW Hole for stuffing tube Upper Half Lower Half Saw along slope of hull. Construction of fairing block 3. Drill a hole just large enough to pass the threaded stuffing t ube of the transducer through the hull, making sure it is drilled vertically. This may require a certain amount of experiment ation for fine tuning at high cruising speeds. Page 34 28 2 to 5 T ransducer Brac ket Hull Epo xy mater ial 525-5PWD, mount ing 4.4 Inside-hull T ransd ucer The thru-hull mount transducer (520-5PSD, 520-5MSD) may also be installed inside the hul l, following the procedure below. Mounting l ocation T o ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Page 38 32 4. Repeat step 1 to ensure that the angle of the sensor is correct. Page 39 33 4. Position the second cable clamp halfway between the first clamp and the cable hole. Flange Nut Coat with silicone sealant. T ape connectors with vulcaninzing tape and then vinyl tape to waterproof them.

Bind tape ends with cable ties to prevent tape from unraveling. SIMULA TION On TEST. Page 43 37 GPS W AA S: Chooses how to use the WA AS signal when connecting with a WA AS receiver, for example GP -320B. Note: WAAS is cur rently in the development al phase. During the development al phase the reliability and availability of the WAAS signal cannot be guaranteed.We should do this for several simple reasons: First of all view first pages of the manual, you can find above. You should find there the most important technical data Furuno Ls4100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Furuno Ls4100 you will learn all the available features of the product, as well as information on its operation. The information that you get Furuno Ls4100 will certainly help you make a decision on the purchase. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Furuno Ls4100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Furuno Ls4100 along with tips on how to solve them.

furuno lcd sounder ls 6000 manual

8 Bottom-zoom display Bottom-zoom display Bottom-lock display The bottom-lock display provides a normal picture on the right half of the screen and a. 1.5 Menu Operating Procedure The LS-6100 has three menus: Main menu (referred to in text as “menu”), System and Installation. Below is the basic menu operating procedure. Page 1 or Page 2 of the menu appears depending on the page last used. The auto mode in use is shown as (Auto-Fishing) or (Auto-Cruising) at the top left corner on the screen. Range offset To display the bottom tail in detail in the automatic mode, offset the range as below. ADVANCE from page 1 of the menu. Picture advancement is stopped until step 3 is completed. Press the MARK key again. The latitude and longitude position at the cursor is output to the navigator and a vertical line marks location. Use the MODE key to select the nav data display you want to set up. Press the Cursor Pad to display the NAV DATA SETUP window. SYSTEM MENU PAGE 1 LANGUAGE English. TLL (Target Latitude, Longitude) position when the MARK key is operated. “TLL” outputs latitude and longitude position. “FURUNO-TLL,” available with connection of navigator that can output FURUNO TLL, outputs latitude and longitude, water temperature, depth, etc. BEARING: Ship’s course and bearing to a waypoint may be displayed in true or magnetic bearing. Page 3 BASIC RANGE 1 - BASIC RANGE 8: Set range of each of the eight basic ranges. Note 1: All default basic ranges are restored whenever the depth unit is changed. Therefore, change the depth unit before changing the basic ranges. Note 2: A range may not be lower than the range preceding it. TEST: Conducts diagnostic tests. For further details, see paragraph 3.7. LCD PATTERN: Tests the LCD. For further details, see paragraph 3.8 MEMORY CLEAR: The memory can be cleared to start afresh with default menu settings. MAINTENANCE, TROUBLESHOOTING WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment.

• furuno lcd sounder ls 6000 manual, furuno lcd sounder ls 6000 manual, furuno lcd sounder ls 6000 manual download, furuno lcd sounder ls 6000 manual pdf, furuno lcd sounder ls 6000 manual instructions, furuno lcd sounder ls 6000 manual free.

It packs 300 Watts (2,400 p-p) of output power for unparalleled fish finding performance. The LS-6100 offers dual frequency (50 and 200kHz) for a two-way view of the world below your boat. This unit is compact enough to fit practically anywhere. Yet it features a 6 silver brite LCD display that offers a remarkably detailed picture of fish and bottom structure. User manual for the device Furuno COLOR LCD SOUNDER FCV-600L. Online user manual database.. 6' ECHO SOUNDER LS-6100. All rights reserved. Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service. Do not maneuver the vessel based on the depth indication alone. The installer of the equipment is solely responsible for the proper installation of the equipment. FURUNO will assume no responsibility for any damage associated with improper installation. Use the specified power cable. Thank you for considering and purchasing FURUNO equipment. Features The FURUNO LS-6100 is a dual frequency (50 kHz, 200 kHz) monochrome LCD echo sounder. Comprised of a display unit and a transducer, the LS-6100 displays underwater conditions on a bright 6-inch monochrome LCD. OPERATION 1.1 Control Description How to remove the hard cover Place your thumbs at the center of the cover, and then lift the cover while pressing it with your thumbs. Single frequency display 50 kHz The sounder uses ultrasonic signals to detect bottom conditions. The lower the frequency of the signal, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. 200 kHz The higher the frequency of the ultrasonic signal the better the resolution. Bottom-zoom display This mode expands bottom and bottom fish in the range width set with ZOOM RANGE on page 3 of the SYSTEM menu. This mode is useful for determining bottom contour. Single frequency display Bottom 29.

If the retaining cover near the top of the bracket is closed, open it by depressing the latch and rotating the cover downward. Install them as shown below. Mounting considerations Choose a suitable mounting location considering the following: Choose a place free from vibration. Choose a mid-boat flat position. The power voltage must be at least 12 V to feed power to those units.Would you like to try it too? Please try again later. There are four display modes to choose from: Normal, Bottom-Lock Expansion, Marker Zoom and Nav Data. A-scope presentation is also available at any time. The LS-6000 has an Auto Mode. This allows “handsoff” operation by automatically switching depth range and adjusting sensitivity depending on the depth of the water. The compact display unit is waterproof, making it ideal for flying bridge installation. Its LCD screen also gives excellent readability even in broad daylight. R Page 2: 1. Display 6-inch monochrome LCD, 3 Thank you, for helping us keep this platform clean. The editors will have a look at it as soon as possible. Do not assume any additional items will be included in your shipment.There are times a display is used ONLY to show the item being sold is functional and working properly. In this case these displays ARE NOT included, this will be stated in our descriptions. If you have ANY questions feel free to send a message or call Max Marine Electronics Inc, Pompano Beach, Florida. We always want to be transparent with our customers and fully disclose any information regarding the products we sell. A solution-minded staff, well versed in product functionality, compatibility and repair, is key to your satisfaction. The LS-6100 offers dual frequency capabilities, both 50 and 200 kHz, for a two-way view of the world below your boat. The fish finder also packs 300 Watts (2,400 p-p) of output power for unparalleled fish finding performance, making this sounder the leader in its fish sonar class. The Furuno LS6100 6?

Only qualified personnel should work inside the equipment. 3.1 Maintenance Regular maintenance is essential for good performance. Checking the items listed in the table below monthly will help keep your equipment in good shape for years to come. 3.6 Troubleshooting The table below provides basic troubleshooting procedures which the user may follow to restore normal operation. Troubleshooting table If Then check neither echo nor battery voltage. Fixed range scale fuse. Appears power supply. No echo appears if display advance but the fixed speed is set to “Stop.”. The ROM, RAM and NMEA port are checked, with the results shown as OK or NG (No Good). For any NG, request service. (A special connector is required to test the NMEA port. Nothing appears if no connector is connected.) 5. INSTALLATION 4.1 Display Unit Mounting considerations The display unit can be installed on a desktop, on the overhead or flush mounted in a panel. When choosing a mounting location keep the following in mind: Keep the display unit out of direct sunlight. For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. 520-5PSD 520-5MSD Thru-hull mount transducer mounting. Hole for stuffing tube Upper Half Lower Half Saw along slope of hull. Install the transducer parallel with water surface. 4.4 Inside-hull Transducer The thru-hull mount transducer (520-5PSD, 520-5MSD) may also be installed inside the hull, following the procedure below. If the bottom is displayed in dark gray and the depth indication appears, the mounting location is suitable. Go to “Final preparation.” 11. If the bottom is not displayed in dark gray tone, the mounting location may be unsuitable. If you do not know the transom angle, temporarily attach the bracket and sensor to the transom to determine if the plastic shim is needed. DO NOT tighten the screws completely at this time. Attaching the sensor to the bracket 1.

Do not disassemble or modify theThe picture is not refreshed whenFire, electrical shock or serious injuryManeuvering the vessel in this conditionImmediately turn off the power at theUse the proper gain setting. Incorrect gain may produce wrong depthContinued use of the equipment canFURUNO agent for service.Use the proper fuse. The high quality LCD shows 99.99%Fuse rating is shown on the equipment. Use of a wrong fuse can result inA warning label is attached to theIf the label is missing or damaged,Grounding may result.Name. Warning Label. Type: 02-146-1022. Code No.: 100-306-050. Safety Instructions for the InstallerDo not install the equipment whereFire or electrical shock can result if thePerformance will be affected. The following are guidelines forBe sure no water leaks in at the transducer or sensor mounting location.Water leakage can sink the vessel. AlsoThe sheath of the cable is made ofDo not turn on the equipment with theUse the specified power cable. The transducer may be damaged. Use of other power cable may result inObserve the following compass safeStandardDisplaySteeringOwners. Features. The FURUNO LS-4100 is a dualComprised of a display unit and aCongratulations on your choice of the. FURUNO LS-4100 5” Echo Sounder. We are confident you will see why the. FURUNO name has becomeFor over 50 years FURUNO Electric. Company has enjoyed an enviableThe main features of the LS-4100 areThis equipment is designed andHowever, no machine can perform itsTemperature and Arrival. (Speed andWe would appreciate hearing from you,Thank you for considering andGPS NavigatorWind Indicator. Power supplySpeed sensor. TransducerEquipment lists. Standard supply. Name. Display Unit. Transducer. Triducer (transducer. Installation MaterialsCode No. Qty. RemarksSpare PartsTemplate. C22-00301 (000-146-981, for flush mount). C22-00302 (000-146-982, for bulkhead). Optional equipment. Conversion Cable. Speed Sensor. Inner Hull Kit S. TypeQty. RemarksThru-hull typeCursor Pad.

Mono LCD Echosounder does not include a transducer. Find great deals on eBay for furuno sounder. Shop with confidence. Search among more than 1.000.000 user manuals and. The Ocean The Grand Inquisitor Rarlab. 300 watts RMS 5-INCH LCD SOUNDER Model LS-4100 Actual size Catalogue No. E-396 R The future today with FURUNO's. In addition to it's fish finding capability, the LS6100 fish locator has the unique ability to be a handy navigational organizer when connected to an appropriate transducer or external nav sensor. With a GPS Receiver Input, the 'Mini-Navigator' feature is capable of storing up to 12 'Go To' waypoints with programmable names. Any of the waypoints can be selected as a destination on the fishfinder. This feature helps determine the depth of your tackle. Choose from a variety of modes, including manual or two auto modes, fishing or cruising. The cruising mode uses a higher clutter rejection setting than the fishing mode, making it useful to track the bottom while cruising.The range can be changed manually or automatically; the LS-6100 will redraw an entire echogram so that the contour can be shown seamlessly. Post navigation Contoh Karangan Faedah Program Kitar Semula Arisaka Type 38 Serial Number Lookup Search Recent News Watching Movies With The Sound Off Download Audiocastle Download Sketchup Pro 2015 Free Mac Download How I Met Your Mother Season 4 Full Torrent Microsoft Visio Portable Free Download babysitemuscle.web.fc2.com. SYSTEM OVERVIEW. ivAdjusting Display Contrast. Brilliance.2Speed.8Cleaning the Display Unit. 21. Transducer Maintenance. 21. Replacing the Fuse. 21. Battery Voltage Alert. 21. Troubleshooting. 22. Diagnostics. 22. Test Pattern. 23. Memory Clear. 23Thru-hull Mount Transducer. 24. Transom Mount Transducer. 26. Inside-hull Transducer. 28. Optional Triducer. 29. Optional WaterDo no turn on the equipment with theThere are no uer-serviceable partsThe transducer may be damaged.

Fish level optionsNote: The audio and visual alarms areWeak: Weak echoes (weakest toneMedium: Medium strength echoesStrong: Strong echoes (darkest toneWaypoints may be used to:Note: Requires latitude and longitudeNote: If there is no position data theCheck the navigator.Waypoint data display. Note: If you attempt to enter 13thTLL or FURUNO-TLL is selected at. TLL OUTPUT on the System menu,A vertical line marks location. Further,The name mayLIST from page 2 of the menu. Erasing waypointsNote: You cannot erase a waypointSet a destination waypoint to find range,Time to Go digital display. Erase? New waypoint window, name entryOffLIST from page 2 of the menu.Waypoint listDisplaysFour-data. Two-dataItems displayable in (1) - (3): depth, position,Items displayable in (4) - (9): depth, position,NAV DATA-1 or 2 display, whicheverNAV DATA SETUP window.NAV DATA SETUP windowNote: You can choose the number ofNAV DATA-1 and NAV DATA-2 on the. System menu.XTE scaleName. Range,Rng 0.19nm. XTE 0.00nmCourse. DestinationBearing toDepthCourse. Brg. Wind Dir.Trip meterWind Speed. SpeedOdometerNO FIX: Position cannot be found. GPS 2D: 2D (dimension) GPS position fix. GPS 3D: 3D GPS fix. GPS W2D: 2D WAAS position fix. GPS W3D: 3D WAAS position fix. Note 1: Nav data is updated with someNote 2: When data is lost 120 sec., theNAV data display-2. This section describes the menu itemsPage 1The white line feature displays theTwo picture color arrangements areNote: To reset the odometer to zero,Mesh as appropriate. “Mesh” paintsIf the gain is too high or too low, or theHow white line worksPage 2RESET? from page 2 of the menu.Page 1. LANGUAGE: The system language isBATT VOLTAGE: Off. SPEED UNIT: Choose unit of speedPage no.WIND UNIT: Choose unit of wind speedTEMP SOURCE: Own. SPEED SOURCE: OwnOwn temp. TEMP UNIT: Choose unit ofFahrenheit. Requires temperature data.

TEMP GRAPH: Turns the waterScaleZOOM MARKER: OnGraphNAV DATA-1, -2: Choose the number ofWATER TYPE: Choose the water typeSalt or Fresh.Apparent: The direction (in relation toTrue: The speed and direction (inKEY BEEP: Turn key beep on or off. BATT VOLTAGE: Turn the batteryWhen on it replaces the picture advancePage 2. NAV DISPLAY: Choose the nav data toYou may chooseTRIP SOURCE: Choose speed sourceTEMP SOURCE: Choose source ofNav window. SPEED SOURCE: Choose source ofNMEA0183: Choose NMEA version ofTEMP CALIB.: If the water temperaturePage 3Note 1: All default basic ranges areNote 2: A range may not be lower thanFor example, ifZOOM RANGE: Choose the range toZOOM MARKER: The zoom markerMaintenanceDo not open the equipment. Only qualified personnel should workRegular maintenance is essential forChecking. ItemThe fuse in the power cable protects theAction. TransducerCheck cable for damage. Power cable,Check that they are tightlyDisplay unitCheck for corrosion. CleanUse the proper fuse. Power supplyCheck voltage. If out ofFuse rating is shown on the equipment. Use of a wrong fuse can result in fire andUnit. A battery icon appears when the batteryDust or dirt on the display unit can beIf desired, aUse special care when cleaning the. LCD since it scratches easily. Do notBattery icon and meaning. Icon. Meaning. Voltage is lower than 10 VDC. If theVoltage is higher than 16.5 VDC. If theThe table below provides basicIf you feel your unit is not workingTroubleshooting tableInstallation menu appears.Installation MenuLevel barTemperature. Battery Voltage. TemperaturePower: 12.4 V. Only when GP-310B is connected. Test displayOK or NG (No Good). For any NG,Nothing appears if no connector isThe memory can be cleared to startThis feature tests for proper display ofInstallation menu.Mounting considerations. See the instructions on the bulkhead orThe display unit can be installed on aTransducerStandard compass: 0.4 meters. Steering compass: 0.3 meters. Transducer mounting location.

Selects menu items;Selects display mode.Selects basic display range.Display unit. How to remove the hard cover. Place your thumbs at the center of theThe unit beeps, the startup screenContact your dealer.) You mayStart-up screen. To turn off the power, press and holdFrequency. Seven displays are available: singleNote: The example screens shown inContrast, BrillianceMinMinMaxDual frequency displayThe 50 kHz picture appears on the left;The sounder uses ultrasonic signals toThe lower theThe higher the frequency of theMarker-zoom displayThis mode expands chosen area of theFrequency and coverage area. Picture Advance Speed. ModeSingle frequency display. FrequencyMarkerEach barZoomedTransmission 20. Fish. School Line. FishMarker-zoom displayNav data displays. This mode expands bottom and bottomRANGE of the SYSTEM menu. ThisThe nav data displays appear on the leftYou can display between two and fourDATA-2” in paragraph 2.1 to choose theZoomBottom-zoom displayBottom-zoom display. Trip meter. Bottom-lock displayThe bottom-lock display provides aThis mode is useful for detecting bottomNAV DATA-1 displayThis sectionSample NAV DATA displaysBottom displayed flat. Bottom-lock displayProcedure. Off. Cruising. Fishing. The LS-4100 has three menus: Main. System and Installation. Below is theAuto mode options windowSince “Cruising” uses a higher clutterChoosing the manual mode. The auto mode in use is shown asNote: When in the auto mode, SHIFTRange offset. To display the bottom tail in detail in theChoosing range. The basic range and range shiftingNote that if the basic range isChoosing basic range. The basic range may be chosen withDefault ranges. Gain offset. Gain offset lets you override automaticUnitMax. Auto gain offset window. Basic RangeUse the proper gain setting. Incorrect gain may produce wrong depthShifting the range. The basic range may be shifted up orWindow can beGain too high Gain proper Gain too low. Examples of proper and improper gainDisplay.

Range and display shift conceptMaxShift windowNote: The picture may not be displayedThe VRM (Variable Range Marker)Fast. Slow. Picture and picture advancement speedHow to measure depth with the VRMAdvance Speed. The picture advance speed determinesNote that theManeuvering the vessel in this conditionInterferenceLevel Noise. Interference from other acousticTo suppress interference, do theMedium, or High (highest).Low intensity “speckles” may appearCLUTTER on the menu. When theTo suppress lowTo turn off low-level noiseInterference fromElectrical interference. Forms of interference. Turn the noise limiter off when noClutter appearanceEchoesThis display shows echoes at eachIt is useful forSediment in the water or reflectionsWeakNote: In the dual frequency display, the. A-scope display is only available withSingle frequency display. Appearance of weak echoesLEVEL from page 1 of the menu.High (highest).StrongStrongA-scope displayA-scope presentation type desired. Normal: Display shows echoes atPeak: Peak-hold amplitude picture.To turn off the signal level function. To turn off the A-scope display,Alarm description. The LS-4100 has six conditions whichBottom alarm: The bottom alarm alertsPageInsideGray characters mean alarm is inactive. Alarm menuWater temperature alarm: The waterOff. On. Inside. Outside. Fish, Arrival, Temp, Speed. Bottom Alarm Alarm Types. Speed alarm: The speed alarm alertsAlarm options. Off: Alarm off, On: Alarm on. Inside: Alarm generated whenOutside: Alarm generated whenArrival alarm: The arrival alarm alertsActivating an alarmDepthTemperature. Speed. Alarm range. Depth, temperature, speed settingStartingAlarm range markerHow the alarm works. Note: To disable an alarm, choose OffSilencing the buzzer. The buzzer sounds and the appropriateYou can silence theWeak. Medium. Strong.

The thru-hull mount transducerThe performance of this sounder isNoise from the propellers alsoDesktop, overhead mountingTypical thru-hull mountRubber Washer. Fairing. Block. HullRubber. WasherWasher. Flat Hull. Thru-hull mount transducer dimensions. Typical thru-hull mountAcceptable transducer mountingProcedure for installing theFabricate the fairing block as shownSuitable transducer mounting locationsDO NOT paint the transducer. Performance will be affected.Transducer. The transom mount transducer is veryDo not use this method on an inboardLower Half. Saw along slopeConstruction of fairing blockBe sure that the transducer isNote: Do not over-stress the stuffingDeep-V. HullInstalling the 520-5PWD on a flat hull. A suitable mounting location is at leastTransducer preparation. Before putting the boat in water, wipeM5 x 14. No. 2Transom mount transducer,No.1. M5 x 14Parallel with hull. Hull. TransomTape. Mount at the stripe. Transom. Transom mount transducer,StripeInstalling the transom mountThis method is employed on deep-VInstalling the 525-5PWD. Referring to “Installing the 520-5PWD”Bracket. TransducerHullEpoxy material. CenterlineTransducerTransducerInside-hull transducer mounting location. Attaching the transducer. The thru-hull mount transducerLightly roughenNecessary tools. You will need the following tools. Remarks on installationTransducer. Silicone. SealantChoosing the mounting location. Coating transducer faceChecking the installationAuto mode.Triducer 525ST-MSDRelease Bracket 525ST-PWD isPre-test for speed and temperature. Final preparation. Support the transducer with a piece ofLet the transducer dry 24-72 hours. Connect the sensor to the instrumentCheck for aTools and materials needed. Scissors. Masking tape. Safety goggles. Dust mask. Electric drill. Drill bit for. Fiberglass hull: chamfer bitScrewdrivers. Straight edge. Marine sealant. Pencil. Zip-ties. Water-based antifouling paintMounting location on single drive boat.

Note 4: For twin drive boat, mountMounting location. To ensure the best performance, theMount the sensor close to the centerlineInstallation of bracketAllow adequate space above theHeight withoutHeight withP66 Installation templateHeight. Height required at mounting locationNote 1: Do not mount the sensor in anNote 2: Avoid mounting the sensorNote 3: For single drive boat, mountAlign arrow with bottom of transom. Align template vertically. Deadrise angle. Slope of hullAlign template arrow withPositioning the templateFiberglass hull: Minimize surfaceIf a chamfer bit or countersink bit isSkip to step 3 in “Adjusting”. Other angles: The shim is required. Skip to step 2 of “Adjusting”. If you do not know the transom angle,NOT tighten the screws completelyAdjustingSensor position and transom angle.