furuno gp-3500 manual

Note: If you make a value mistake, move the cursor to the error position and then re-enter the proper value. The course is at the top of screen at the moment the pilot display is selected. A filled triangle marks own ship’s position. When setting a destination, the NAV INFO 1 (2) window changes to the WPT INFO 1 (2) window. INFO windows. For further details, see paragraph 9.6.2. 2.1.4 Compass plotter (or pilot) display The compass display, displayed at the top of the screen in a combination display, provides steering information. Note: The course means the direction of own ship’s movement, it is not the direction of heading. Receiving signal level Bars show satellite signal levels. Satellites whose signal level extends 40 are used to fix position. The cursor is turned on, and the cursor appears at the own ship’s position. PLOTTER NAV INFO 1 display (appearing the cursor) 2. The display shifts in the direction which the trackball is rolled. When you insert a suitable chart card in the right side slot and turn on the power, a chart appears. If a wrong card is inserted or a wrong chart scale is selected, landmasses will be hollow. These frames are called indices and they show you what parts of the chart can be zoomed. The areas circumscribed with smaller frames can show more detailed information. When connecting with an ARPA-equipped radar, other ship’s track can also be plotted. This chapter shows you how to turn track on or off, and change its color and plotting interval. Own ship’s track is displayed in red in the default setting. Note that the sub track is not stored in the memory; it is erased when it goes off the screen or when the power is turned off. Note that this track is not stored in the memory; it is erased when it goes off the screen a when the power is trued off 1. It can be useful to change track color on a regular basis to discriminate between previous day’s track, etc.

• furuno gp 3500 manual, furuno gp-3500 installation manual, furuno gp-3500 manual, furuno gp-3500 manual pdf, furuno gp-3500 manual download, furuno gp-3500 manuals, furuno gp-3500 manual instructions.

All rights reserved. Pub. No. OME-44210 Pub. No. OME-44210 ( ( TATA TATA ) ) GP-3500 GP-3500 The paper used in this manual is elemental chlorine free.Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service. Keep heater away from equipment. A heater can melt the equipment's power cord, which can cause fire or electrical shock. The display unit is totally integrated GPS receiver and color video plotter. The GPS receiver tracks up to thirteen satellites (GPS: 12, WAAS: 1) simultaneously, and an 8-state Kalman filter ensures optimum accuracy in determination of vessel position, course and speed. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Invalid operation causes the unit to emit three beeps. Card slot Opens the BRILLIANCE window. Momentary press: Registers own ship's positions. Long press: Marks man (more than overboard. It has six keys, all of which may be programmed by the user. Hole for hooking. ZOOM IN ZOOM OUT The default key functions are as below. Function Enter a waypoint with the next consecutive waypoint number at the own ship (or cursor) position. Insert the appropriate chart card for your area before turning the power on to show chart data automatically. The brilliance adjustment window appears. Note: The adjustment window disappears when there is no operation for three seconds. You may also choose the hue by pressing the appropriate numeric key. A DISPLAY MODE screen appears. There are four pages for the DISPLAY MODE screen. Operate the trackball to place the cursor on the MOB mark.All keys are operative. “DEMO” appears at the bottom of the plotter (pilot) display (top of the sounder display) when any simulation mode is active. This manual uses method a). Press the appropriate numeric key.

A flashing diamond mark appears over the waypoint when it is correctly selected. The sequence of waypoints leading to the ultimate destination is called a route. Entering Routes You can store up to 200 routes and a route may consist of 35 points. For automatic entry, you will or need to set interval of tune or distance. This feature is useful when you wish to retrace a track. Then, the display shows the locations of those services nearest you. (The figure below shows the location of a fitting station in an area in southern Italy.) Use the cursor pad to place the “hand cursor”. A light-blue line runs between destination selected and own ship’s position. Arrows on the line show the direction to follow. Range and bearing from own ship’s position to destination appear at the top of the screen. Selecting waypoint from the history list The latest five waypoints entered are saved to the history list. Last-entered waypoint GOTO WAYPOINT 00000 WAYPOINT 000005 000004 000003. In the figure below, for example, the vessel has decided to navigate from waypoint 05 to 03, skipping waypoint 04. Waypoint 1 PORT 1 Waypoint 6 PORT 2 1. PERPENDICULAR: ARRIVAL ALARM: Waypoint 1 PERPENDICULAR To select waypoint switching method, do the following. 1. When an alarm setting is violated, the buzzer sounds and the speaker icon ( )and type of alarm appear. The alarm will be released if your boat enters the circle. Start point The border alarm defines an area, defined by two waypoints, which you do not want to cross. The distance is called the proximity alarm radius. You can globally activate or deactivate the proximity alarm here. There are two types of water temperature alarms: INSIDE and OUT. The INSIDE alarms sounds when the water temperature is within the range set, and the OUT alarm sounds when the water temperature is higher or lower than the range set. 1. The bottom alarm sounds when the bottom echo is within the alarm range set.LIGHTHOUSES Turns lighthouse viewing sector on or off.

For own ship’s track, track color can be changed automatically according to water temperature or depth. Changing own ship’s track color by preset temperature range This method changes the color of track when the water temperature is within a preset range. Changing track color by preset depth range This method changes the color of track when the depth is within a preset range. For example, you can set up to paint the track yellow when the depth is between 200 and 300 feet. Be absolutely sure you want to erase track; erased track cannot be restored. Note 1: Files set to “YES” on the DISPLAY DATA FROM MEMORY CARD menu cannot be erased. A green dot appears on the starting point.Note 1: Files set to “YES” on the DISPLAY DATA FROM MEMORY CARD menu cannot be edited. (See paragraph 10.2.3.) Also, files set to “YES” on the DISPLAY DATA FROM INTERNAL MEMORY menu cannot be edited. If you require a different apportion you may change it as shown in the procedure below. Marks can be inscribed in 11 shapes and seven colors of red, yellow, green, light-blue, purple, blue and white. Note that the erased marks and lines cannot be returned. Note: Files set to “YES” on the DISPLAY DATA FROM MEMORY CARD menu cannot be erased. AREA a) Operate the trackball to move the cursor to the starting point of the area.Note: Files set to “YES” on the DISPLAY DATA FROM MEMORY CARD menu cannot be erased. (See paragraph 10.2.3.) Also, files set to “YES” on the DISPLAY DATA FROM INTERNAL MEMORY menu cannot be erased. A waypoint is the simplest piece of information your equipment requires to get you a destination, in the shortest distance possible. Entering Waypoints This unit has 3500 waypoints into which you can enter position information. The SAVE WAYPOINT window appears.You can enter numeric data with the numeric keys. Note: If you enter a wrong character, re-enter the correct character after placing the moving the character cursor on the wrong character.

For that reason, you may want to record the current display before replaying data. Note 2: Loaded and current data are processed as follows: Tracks: Since loaded track data is added to internal track, oldest track will be erased when the track memory capacity is exceeded. There are two backup methods; backup by a memory card and backup by the internal memory. Note that this function may delay the normal display after the turning power on. Data are saved and replayed between the working memory and internal memory. 10.4.1 Saving data to internal memory Data in the working memory can be saved in internal memories. The total number of points for tracks, marks and lines is 16,000. The message “NOW SAVING DATA TO INTERNAL MEMORY.For that reason, you may want to record the current display before replaying data. Note: When waypoint or route data are uploaded, all data in the internal memory will be replaced with the uploaded data. 1. Connect the PC to the equipment. 2. See Note 2: Number of sentences currently used (1 to 4) 3: Message mode (Always set to C) 4: Route No. Location Antenna unit Check for loosened and corroded bolts. Antenna cable Check connection point for watertightness. If the fuse blows, find the cause before replacing it. Use only a 3 A fuse. Using the wrong fuse will damage the unit and void the warranty. If you cannot restore normal operation do not attempt to check inside the unit. Any trouble should be referred to a qualified technician. These mean no problem. The GPS receiver is shipped with no Almanac in its memory. When the power is first turned on after installation the receiver starts receiving the Almanac. Shape: Color: RED, YEL, GRN, L-BLU, PPL, BLU, WHT North marker points to North. Correct chart and suitable scale. Chart over-enlarged. Chart card not inserted. Wrong chat card. Chart scale too small. Alarm setting violated. Furuno will accept no responsibility for the use of the signal for other than the above stated purpose.

For how to set the data window, see paragraph 9.6.2. Display setup menu (page 1) 9-13. For details, see the installation manual. NMEA DEPTH CALIB You can apply an offset to NMEA depth data. This causes a difference between the true and magnetic north location. This difference is called magnetic variation, and varies with respect to the observation point on earth. For details, see the installation manual. When selecting EXT, EXT LORAN-C or ALL, “EXT” appears at the bottom of the PLOTTER (PILOT) display. Using this information, the GPS receiver automatically eliminates any malfunctioning satellite from the GPS satellite schedule. However, the Almanac sometimes may not contain this information. To lessen the time required to find position, you may enter your position manually. For MANUAL, enter appropriate WAAS satellite number, referring to the illustration below.The setup menu appears. You may select the data to display and where to display it as follows: 1. Be sure to set the ports correctly: Improper setting may prevent proper transfer of data. Do not forget the password. If you forget the password, contact a FURUNO agent or dealer for advice. (The serviceman will restore default settings, all waypoints and marks are erased.) 1. Formatting prepares the card for use with the system. To format a card, do the following procedure. Note: Formatting a memory card erases all data from the card. There are two methods to enter data: save data to a new file or save it to an existing file in which the previous data is written over. The message “NOW SAVING DATA TO MEMORY CARD. DO NOT TURN OFF DISPLAY UNIT UNTIL COMPLETED.” appears. When saving is completed, “COMPLETED SAVING DATA.The overwriting starts. The message “NOW SAVING DATA TO MEMORY CARD. DO NOT TURN OFF DISPLAY UNIT UNTIL COMPLETED.” appears. When the overwriting is finished, the message “COMPLETED SAVING DATA. PRESS KNOB TO CONTINUE.” appears.

You can inscribe this mark from any mode, except while playing back, recording data or conducting a self-test. If you select the MOB position as the destination; This line shows the shortest course to the MOB position. All keys are operative. You may choose the setting by pressing the numeric key. Go to step 10. 8 FIGURE: Track is traced in a figure-eight course. Go to step 12. This section provides basic menu operating information. This manual uses method a). You can also select item by rolling the trackball in up-down direction. The cursor for entering value is moved by rolling the trackball in left-right direction. The plotter display orientation is always north-up. North (zero degree) is at the top of the display and own ship (filled circle) is at the center of the screen. The course is at the top of screen at the moment the pilot display is selected. A filled triangle marks own ship’s position.When setting a destination, the NAV INFO 1 (2) window changes to the WPT INFO 1 INFO windows. For further details, see paragraph 9.6.2. The cursor includes the affect of current and wind. The range of the depth graph is 50 feet and it is automatically adjusted with depth. It is shown in black when the amount of cross-track error is within the XTE monitor range and yellow when it is over. An arrow appears at the right or left side of the XTE monitor and it shows the direction to steer to return to the intended course. The arrow is shown in red when you should steer left, and green when you should steer right. In the example on the previous page you would steer right to return to course set. To maintain course, steer the vessel so the own ship marker stays at the center of the XTE monitor. Satellites whose signal level extends 40 are used to fix position. The smaller value means the higher accuracy. (For your reference, the positioning accuracy is approx. 10 m when the value is less than “4”.

) The higher the number the stronger the received signal, and a figure above 60 is normal. The higher the SN ratio the better the quality of the signal, and a figure above 21 is normal. The display is enlarge or shrunk from the screen center. The range value shows the distance between the left-side and right-side edges of the screen. See paragraph 2.7. See paragraph 9.2.3. See paragraph 9.3. Its radius is also fixed. When cursor is turned off, VRM appears around own ship’s position. Also, a data box appears at the top of the display to show the radius of VRM. Clockwise rotation: Increase radius. Counterclockwise rotation: Decrease radius. Its function can be changed as desired. For details, see paragraph 9.5.1. When you insert a suitable chart card in the right side slot and turn on the power, a chart appears. If a wrong card is inserted or a wrong chart scale is selected, landmasses will be hollow. Insert the proper card and select a suitable chart scale. Chart icons appear at the bottom of the plotter (or pilot) display to help you select a suitable chart size. The table below shows the chart icons and their meanings. These frames are called indices and they show you what parts of the chart can be zoomed. The areas circumscribed with smaller frames can show more detailed information. Additionally it displays the times of sunrise and sunset. Time and height are shown below the graph. When connecting with an ARPA-equipped radar, other ship’s track can also be plotted. This chapter shows you how to turn track on or off, and change its color and plotting interval. Own ship’s track is displayed in red in the default setting. Note that this track is not stored in the memory; it is erased when it goes off the screen a when the power is trued off You can stop recording the track, to conserve the track memory, as follows. Each time the key is pressed the track function available changes in the sequence shown below.

It is the user’s responsibility to exercise common prudence and navigational judgment while using the SBAS signal. Only qualified personnel should work inside the Always confirm position against all available equipment.Do not disassemble or modify the equipment. Use the proper fuse. Fire, electrical shock or serious injury can result. Fuse rating is shown on the power cable. Use ofFor over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers. The equipment is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended function unless installed, opeOperation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device muInvalid operation causes the unit to emit three beeps. Card slot Opens the BRILLIANCE window. BRILL POWER Opens the SAVE WPT window. SAVE 3 seconds) position. WPT GOTO MOB Displays the DISPLAY MODE DISP PROG1 MENU screenIt has six keys, all of which may be programmed by the user. Hole for hooking. ZOOM IN ZOOM OUT Label Record the function registered to k A ey. Record the function registered to key. B Record the function registered to k C ey. Record the function registered to k D ey. Note: When proqramming the or key, make a mental note of their proInsert the appropriate chart card for your area before turning the power on to show chart data automatically. Note: Static electricity can be passed through your fingers to a card and destroy the contents of the card. To prevent this, always touch a metallic object, such as a steel desk, before handling Refer to the table shown below the choose appropriate hue settings. Hue setting and item color Day NightTwilightManual Landmass YellowYellowYellow DepA DISPLAY MODE screen appears.

There are four pages for the DISPLAY MODE screen. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. Contact a FURUNO agent for service. Use of a wrong fuse can result in damage to the equipment. Electronic aids are intended to assist, not replace, the navigator. Do not remove the label. If the label is missing or damaged, contact For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers. However, no machine can perform its intended function unless installed, operated and maintained properly. Please carefully read and follow the recommended procedures for operation and maintenance. The display unit is totally integrated GPS receiver and color video plotter. All names mentioned are registered trademarks of their respective companies. Invalid operation causes the unit to emit three beeps. It has six keys, all of which may be programmed by the user. Insert the appropriate chart card for your area before turning the power on to show chart data automatically. To prevent this, always touch a metallic object, such as a steel desk, before handling a memory card. You can go the last-used display faster by pressing any key. The screen you see depends on your system configuration and equipment settings. Thereafter it takes about 12 seconds to find position each time the power is turned on.Adjust it at the external monitor. You may also choose the setting by pressing the appropriate numeric key. You may also choose the hue by pressing the appropriate numeric key. In addition to the full-screen display, you can divide the screen into half-screen combination displays. There are four pages for the DISPLAY MODE screen. You may program the DISPLAY MODE screen as desired. See paragraph 9.6.1.

When plotting is stopped, own ship’s mark changes from a solid circle to a hollow one and track is not stored in the memory. PLOTTER NAV INFO 1 display) In this case own ship’s track is not recorded; it is erased when it goes off screen or when the power is turned off. OFF: Stopping and resuming points are not connected. It can be useful to change track color on a regular basis to discriminate between previous day’s track, etc. For own ship’s track, track color can be changed automatically according to water temperature or depth. Printed in Japan FIRST EDITION: JUL JUL. 2003 F4 Pub. No. OME-44210 ( TATA ) GP-3500: APR APR. Page 3 SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. Do not disassemble or modify the equipment. CAUTION No one navigation device should ever be solely replied upon for the navigation of a vessel. Always confirm position against all available aids to navigation, for safety of vessel and crew. Use the proper fuse. Fire, electrical shock or serious injury can result. Page 4 FOREWORD Congratulation on your choice of the FURUNO GPS COLOR PLOTTER GP-3500. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers. The equipment is designed and constructed to meet the rigorous demands of the marine environment. This GPS receiver complies with Canadian standard RSS-210 (Low Power License-Exempt Radio communication Devices). Page 10 This page is intentionally left blank. Page 11 1. BASIC OPERATION 1.1 Controls Description 1.1.1 Display unit When you correctly execute an operation, the unit generates a beep. Invalid operation causes the unit to emit three beeps. Card slot Opens the BRILLIANCE window. Long press: Marks man (more than overboard 3 seconds) position.

BRILL SAVE MOB WPT GOTO Displays the DISPLAY MODE screen. It has six keys, all of which may be programmed by the user. Hole for hooking. ZOOM IN ZOOM OUT Label Record the function registered to A key. Record the function registered to B key. Record the function registered to C key. Record the function registered to D key. Page 13 1. BASIC OPERATION 1.2 Loading a Mini Chart Card Your unit reads FURUNO and NavCharts (NAVIONICS) chart cards, or C-MAP chart cards, depending on the type of display unit you have. Insert the appropriate chart card for your area before turning the power on to show chart data automatically. Note: Static electricity can be passed through your fingers to a card and destroy the contents of the card. When the unit is turned on, it proceeds in the sequence shown in the figure in below. The brilliance adjustment window appears.You may also choose the hue by pressing the appropriate numeric key. Refer to the table shown below the choose appropriate hue settings. Page 20 1. BASIC OPERATION 1.5 Selecting a Display Five screen displays are available: Plotter, Pilot, Navigation, Compass and Sounder. A DISPLAY MODE screen appears. There are four pages for the DISPLAY MODE screen. DISPLAY MODE 1. PLOTTER 2. PLOTTER NAV INFO 1 3. PLOTTER NAV INFO 2 4. PILOT 5. PILOT NAV INFO 1 6. PILOT NAV INFO 2 7. COMPASS PLOTTER 8. COMPASS PILOT 9. Page 21 1. BASIC OPERATION 1.6 MOB Mark The MOB (Man Overboard) mark functions to mark man overboard position. You can inscribe this mark from any mode, except while playing back, recording data or conducting a self-test.The following message will appear is on the screen: WAYPOINT NAME XXXXXX WILL BE DELETED. Then, the waypoint entered at step 1 on the previous page is erased. Page 23 1. BASIC OPERATION 1.8 Simulation Mode The simulation mode, which is for use by service technicians for demonstration purposes, provides simulated operation to help acquaint you with the many features your unit has to offer.

All keys are operative. “DEMO” appears at the bottom of the plotter (pilot) display (top of the sounder display) when any simulation mode is active.This manual uses method a).The red cursor appears at left side of the item selected.The course is at the top of screen at the moment the pilot display is selected. A filled triangle marks own ship’s position. When setting a destination, the NAV INFO 1 (2) window changes to the WPT INFO 1 (2) window. Speed over ground Latitude, Longitude This color shows the selected mark color. NAV INFO 2 window on setting a destination (default data) Note: You can choose the data to display in the NAV. INFO windows. For further details, see paragraph 9.6.2. 2.1. Page 33 2. PLOTTER AND PILOT DISPLAY DESCRIPTION Compass indicator The black inverted triangle shows the bearing to the destination waypoint, and the red triangle shows own ship’s course. Note: The course means the direction of own ship’s movement, it is not the direction of heading. The cursor includes the affect of current and wind. Depth and water temperature graphs The depth and water temperature graphs, which require appropriate sensors, show the latest 10 minutes of depth and water temperature data. Page 34 2. PLOTTER AND PILOT DISPLAY DESCRIPTION 2.1.5 GPS status display The GPS status display provides data about the GPS satellites and GEO satellite (for WAAS). Estimated position of satellite in the sky. Satellites used for fixing position are circled. 01: 00: 15 APR 1 2003 N 08 05 21 12 07 W 01 GPS 2D 20 E 06 11 28 30 W 03 S SAT No. 30 Receiving signal level Bars show satellite signal levels. Satellites whose signal level extends 40 are used to fix position. The cursor is turned on, and the cursor appears at the own ship’s position. Each pressing this key makes the sequence shown below. The data box disappears immediately. Its function can be changed as desired. These frames are called indices and they show you what parts of the chart can be zoomed.

The areas circumscribed with smaller frames can show more detailed information. Indices Tide information The C-MAP NT chart card provides for calculation of the tide heights for any date. CHANGE DATE (DD. MM. YYYY.) 04. 11. 2003 LIMIT: 31. 12. 2099 DATE window 6. Page 43 3. TRACK Your ship’s track (main and sub tracks) is plotted on the screen using navigation data fed from the built-in GPS navigator. When connecting with an ARPA-equipped radar, other ship’s track can also be plotted. This chapter shows you how to turn track on or off, and change its color and plotting interval. Own ship’s track is displayed in red in the default setting. It can be useful to change track color on a regular basis to discriminate between previous day’s track, etc. CHANGE SHIP'S TRACK COLOR 1. 2. 3. 4. 5. 6. 7. 8. TMP 9. Page 51 3. TRACKS 3.3.4 Automatically changing own ship’s track color by water temperature There are two methods by which own ship’s track color may be changed according to water temperature: by preset temperature range or temperature variation. Changing own ship’s track color by preset temperature range This method changes the color of track when the water temperature is within a preset range.Changing track color by preset depth range This method changes the color of track when the depth is within a preset range.Be absolutely sure you want to erase track; erased track cannot be restored. OR PRESS APPROPRIATE NUMERIC KEY TO SELECT MENU. Page 59 3. TRACKS 9. Do the follows depending on selection made at step 7. 2 PTS Squares (memory points) appear on the track. Own Ship Memory point Track a) Operate the trackball to place the cursor on the starting memory point to erase. A green dot appears on the starting point.Delete ship’s tracks window 4. Page 61 3. TRACKS 3.7 Editing Tracks The color and style of tracks may be edited as desired. If you require a different apportion you may change it as shown in the procedure below.

Note that when the track memory capacity is changed, all tracks and marks in the memory are erased. The default setting allows you to enter 4,000 marks and line points.AREA a) Operate the trackball to move the cursor to the starting point of the area.A green rectangle appears. The SAVE WAYPOINT window appears. Cursor SAVE WAYPOINT WAYPOINT NAME 000001 PRESS NUMERIC KEY TO ENTER WAYPOINT NAME.Note: If you enter a wrong character, re-enter the correct character after placing the moving the character cursor on the wrong character. Edit the waypoint data on the waypoint edit window as appropriate. Note 1: The color and shape of a waypoint whose PRXMTY RADIUS is other than 0.00 cannot be changed. Page 82 5. WAYPOINT 5.3 Erasing Individual Waypoints Individual waypoints can be erased by the cursor or through the WAYPOINTS LIST. You are asked if you are sure to erase the waypoint.Press the appropriate key among 1, 2 and 3 to select the sorting method. ALPHA: Sorting waypoints and MOB in order alphanumeric. DIST: Sorting waypoints in order of decreasing distance to own ship. Page 84 5. WAYPOINT 5.5 Setting Ship’s Speed for TTG Calculation of TTG is based on ship’s speed data. Roll the trackball in left-right direction to select “ACTUAL SPD” or “SIM SPD.” ACTUAL SPD: Calculating with the actual ship’s speed. The sequence of waypoints leading to the ultimate destination is called a route. 6.1 Entering Routes You can store up to 200 routes and a route may consist of 35 points. For automatic entry, you will or need to set interval of tune or distance. This feature is useful when you wish to retrace a track.Waypoint name appears here.A light-blue line runs between destination selected and own ship’s position. Arrows on the line show the direction to follow. Range and bearing from own ship’s position to destination appear at the top of the screen. Selecting waypoint from the history list The latest five waypoints entered are saved to the history list.

furuno gp-1850df manual

5 Cancelling NavigationThe anchor watch alarm informs you that yourThe speed alarm warns when your boat’s The proximity alarm alerts you when your. Page 64 9.8 Alarm Information Alarm messages. When an alarm setting has been violated the Table 9-1 Alarm messages and their meanings.Page 68 This page is intentionally left blank.Page 70 CHART DETAILS menu BACKGROUND: Select background color toPage 71 Display setup1 menu description BEARINGDisplays position in latitude and longitude Selects source of water temperature input;During position fixing, ship’s velocity (speed The default latitude and longitude position isSelect ON to use the DGPS mode. The de- 1. Select GRI and press. Page 76 4. If necessary, you may enter position off- WHITE MARKERThe configuration menu has facilities for set- Selects NMEA0183 version 1.5 or 2.0. If youThis menu allows you.Page 81 Note 2: A route can may contain 35 waypoints SYSTEM menuPage 88 DEPTH INFO soft key: Turns the DEPTH Note 1: Depth data depends on thePage 90 This page is intentionally left blank.Regular maintenance is essential for good WARNINGPage 96 Remote controller test 13.6 Clearing Memories. This test checks the controls of the remote The memory, which stores marks, tracks. Page 97: APPENDIX Menu Tree. MENU keyChain GRI S1 S2 S3 S4 S5. Canadian. Page 101 Decca Chains. Chain Chain Chain Location Chain Chain Chain Location. No. code no. codePage 102 World TimeAlarm information window 2-10, 9-4 DECCA station selection 11-7. ALARM. Page 108 H N. Highway display 3-7 Nav data display 3-5. Hue (sounder) 2-9 NavigationI multiple quick points 8-1. Page 109 Rhumb line 11-2 Track. Routes color 4-2. Connection to the wrong power supply can cause fire or equF0 P14-0240101 04-375-27 Hard cover 6s AccessoThe mini chart card drive in the display unit loads elec- tronic charts. External equipment which can be connected include water tempera- ture and speed sensors, autopilot, and DGPS beacon receiver (GP-1850F).

• furuno gp-1850df manual, furuno gp-1850df manual, furuno gp 1650df manual, furuno gp 1870f manual, furuno gp-1850df manual download, furuno gp-1850df manuals, furuno gp-1850df manual instructions, furuno gp-1850df manual 2017, furuno gp-1850df manual user, furuno gp-1850df manual free, furuno gp-1850df manual downloads, furuno gp-1850df manual transmission, furuno gp 1650df manual.

For detailed information, refer to the operator's manual.Changing the Plot Interval 3. Press the soft key TRACK CONTROL. 4. Do not use the equipment for other thanFOREWORD. iv 4. TRACK. SYSTEM CONFIGURATION. v 4.1 Displaying Track. 4-1OwnersCongratulations on your choice of. Page 7: SYSTEM CONFIGURATION SYSTEM CONFIGURATIONThis chapter acquaints you with the basics of your unit - from turning on the power. Page 10 1.2 Remote ControllerThere are five display modes from which to This mode expands bottom and bottom.Automatic sounder operation is useful whenPress the soft key RANGE to show the range The basic range may be shifted. Page 21 2.8 Suppressing Interference 2.9 Suppressing Low LevelInterference from other acoustic equipmentDirty water or reflections from plankton may The white marker functions to display. Page 23 2.12 Selecting Picture Advance 2.13 Selecting BackgroundThe picture advance speed determines how 1. Press the. Page 24 2.14 Alarms 3. Select the menu item, and press the softBottom alarmZero line Echoes from the bottom are normally theWhen the waters are rough or the boatThe plotter display mainly shows chart, ship’s Press the soft key COURSE. Page 28 3.2 Cursor 3.4 Selecting ChartPage 29 Indices and chart enlargement Chart symbols. When the soft key ZOOM OUT is used, you FURUNO mini chart cardEquipped with a DGPS beacon receiver, your The steering display provides steering infor-The black boat-shaped mark shows own The highway display provides a. Page 34 3.9 Changing Operation Mode 3.10 Navigation Trip Distance. Operation mode can be changed between The navigation trip distance is displayed. Page 35: 4. TRACK 4. TRACKPage 37 PLOT 4.5 Changing Track MemoryBe absolutely sureYou are asked ifPage 48 This page is intentionally left blank.Often a trip from one place to another involves NEWPage 50 Entering routes by the cursor NEWWhen you steer to avoid an obstacle or the Speed, which may be. Page 59 To select waypoint switching method do the 8.

If the label is missing or illegible, contact This dedication to excellence is furthered by our extensive global network of agents and dealers. However, no machine can perform its intended function unless installed, operated and maintained properly. Please carefully read and follow the recommended procedures for operation and maintenance. The GP1850F mostly shares the same features with the GP-1850DF except it does not have a DGPS beacon receiver. On-screen information shown are position, range and bearing to cursor position, range, bearing, ETA and TTG to waypoint, etc. An 8-state Kalman filter ensures optimum accuracy in determination of vessel position, course and speed. When the unit is turned on, it proceeds in the sequence shown in Figure 1-4, after displaying the FURUNO information display. If you want to lessen the time needed to find position you may enter your position manually (default position: San Francisco, USA) on the GPS SETUP OPTIONS menu. Table 1-1 shows these abbreviations and their meanings. The time remaining until the power is turned off is shown on the screen. The tone and brilliance setting menu appears. For details, refer to Chapter 3. Each time this key is pressed, the display mode changes in the sequence shown below. For further details see “Selecting display mode” on page 2-3. Menus may be selected with the five soft keys to the right of menus. Options are selected with the cursor pad. For example, press the soft key SOUNDER SETUP OPTIONS. The menu in use appears at the top right corner of the display. For example, select WHITE MARKER. On the plotter display, own ship tracks, at the speed selected, a figure eight course or any course you enter, starting from position entered. All controls are operative; you may set destination, enter waypoints, etc. Simulated sounder operation is also provided. Select how you want the courseline to be traced; by FIGURE 8 or DIR.(ection). For DIR., enter course. Enter current latitude.

GPA-018 (for GP-1850DF) GPA-017 1.2 m Whip antenna GPA-019 (for GP-1850F) (for GP-1850DFTabletop, overhead mounting 1. Fix the hanger by four tapping screws M5 X 16. 2. Screw knob bolts in display unit, set it to hanger, and tighten knob bolts. 3. Attach hard cover to protect LCD. WARNING Figure 1-2 Tabletop, overhead mounting of display unit Flush mounting Note: Use supplied pan head screws when the thickness of the bulkhead is from 11 to 14 mm. For bulkhead which exceeds 14 mmCoat the trans- ducer face and mounting location with silicone sealant. Transducer face Silicone sealant Figure 1-6 Coating the transducer face with silicone sealant 3. Press the transducer firmly down on the hull andIf the bottom is not displayed in reddish brown, the mounting location is unsuit- able.When the boat has a keel, the transducer should be at least 30 cm away from it. Typical through hull mountings are shown in the figure on the next page. The performance of the video sounder is directly related to the mounting location of the transThere are two methods of installation: flush with hull (for flat hulls) and projecting from hull (for deep V-hulls).If the boat is placed on a trailer care must be taken not to damage the transducer when the boat is hauled out of the water anThe transducer should, therefore, be located in a position where water flow is the smoothest. Noise from the propel- lers also adversely affects performance and the transducer should not be mounted nearby. Shifting the Display Press and hold down the cursor pad. For detailed information, refer to the operator's manual. Sign up now. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. Printed in Japan Only qualified personnel should work inside the equipment. Position may be degraded Do not remove the label.

It is useful for searching fish schools at cruising speed. The width of the sounder display can be selected between standard (approx. 20 mm) and wide (approx. 40 mm). The sounder setup menu appears. See Figure 1-9. This display is useful for comparing the same picture with two different sounding frequencies. It works as follows. It jumps to one step shallower range when bottom echoes reach a half way point of the full scale from top and to one step deeper range when they come to the lower edge of scale. CRUISING is for tracking the bottom, and FISHING is for searching fish schools. CRUISING uses a higher clutter rejection setting than FISHING therefore it is not recommended for fish detection - weak fish echoes may be erased by the clutter suppression circuit. The basic range can be thought of as providing a “window” into the water column and range shifting as moving the “window” to the desired depth. Press the soft key RETURN to finish. Current level is shown above the bar. Press the RETURN key to finish. This can be done with the soft keys GAIN 50kHz and GAIN 200kHz. Use a higher gain setting for greater depths and a lower setting for shallow waters. Press the soft key RETURN to finish. The higher number the greater the degree of suppression. This is mainly due to dirty water or noise. This noise can be suppressed by adjusting CLUTTER on the SOUNDER SETUP OPTIONS menu. To suppress low level noise in manual sounder operation do the following: Note that weak echoes may not be displayed when the clutter circuit is on. These weak echoes may be erased as follows: The higher the number the stronger the echo will be erased. For example, you may want to display the bottom echo (red- dish-brown) in white to discriminate fish echoes near the bottom. Note that the bottom must be displayed in reddish-brown for the white marker to function. When you select 8 in HUE window (See page 2-9.), white marker is among 0 to 8.

Enter current longitude. It does this by utilizing the fact that an ultrasonic wave transmitted through water travels at a nearly constant speed of 4800 feet (1500 meters) per second. When a sound wave strikes an underwater object such as fish or sea bottom, part of the sound wave is reflected back toward the source (transducer). Thus by calculating the time difference between the transmission of a sound wave and the reception of the reflected sound wave, the depth to the object can be determined. Transmitter power is sent to the transducer as a short pulse of electrical energy. The electrical signal produced by the transmitter is converted into an ultrasonic signal by the transducer and transmitted into the water. Any returning signals from intervening objects (such as a fish school) are received by the transducer and converted into an electrical signal. The signals are then amplified in the amplifier section, and finally, displayed on screen. Each line represents a snapshot of what has occurred beneath the boat. A series of snapshots are accumulated side by side across the screen, and the resulting contours of the bottom and fish between the bottom and surface are displayed. To switch between these pictures, do the following: The lower the frequency of the pulse, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. Therefore, the 200 kHz frequency is ideal for detailed observation of fish school. Press the soft key RETURN to close the window. The length of the segment is equal to one division of the depth scale. A bottom displayed with a short echo tail usually means it is a soft, sandy bottom. A long echo tail means a hard bottom. This mode is useful for bottom discrimination. It may be turned on in the DISPLAY SETUP2 menu. For further details see “ZOOM MARKER” on page 9-4. It is useful for estimating the kind of fish school and seabed composition.

The hollow inverted triangle shows the bearing to destination waypoint. When own ship’s course is changed, the hollow inverted triangle moves with course change. Using Figure 3- 13 as an example, you would steer right by 000.02 nautical miles to return to course. When this mark is out of range of the XTE scale, the mark color changes from black to yellow. The range of the XTE scale can be set as shown below (default: 0.5 nm). To cancel entry, press the soft key CANCEL. It is useful for monitoring XTE - the XTE scale shows direction and amount in nautical miles to steer to return to course. In the figure below, for example, you would steer right by 0.02 nm to return to course. Equipment Lists. ii. System Configuration. ivN ishinom iya, Japan. Te l e p h o n e. Te l e f a x:Printed in Japan. PU B. N o. IM E-43950-JGround the equipment toConfirm that the power supply voltageHazardous voltage which canConnection to the wrong power supplyTurn off the power at thePost a sign near the switchUse the correct fuse. Use of a wrong fuse can cause fire orFire, electrical shock orKeep the following compass safeStandard Steering. Display UnitWhen handling the transducer cable,The sheath of the transducer cable isEquipment Lists. Standard supply. No.Type. Code No. Qty. RemarksDisplay unit. Antenna unit. TransducerOptional equipmentType. Remarks. GPA-018, GR-7000A, whipBeacon receiver GR-902-1850-15A-018SCode No. Antenna cableNo.13-QA330No.13-QA310No.13-RC5160Optional equipment (con't). No. Name. Type. RemarksTemperatureReceiverSystem ConfigurationA DGPS beacon receiver is provided inside the displayThe mini chart card drive in the display unit loads electronic charts. External equipment which can be connected include water temperature and speed sensors, autopilot, and DGPS beacon receiver (GP-1850F).GPS satellite and beaconBoxTemp. sensorTransducerDGPS beacon receiver. GP-1850F onlyMounting considerations.

The display unit can be installed on a tabletop, on the overhead or flush mountedHard Cover. Tabletop. Overhead. Figure 1-1 Tabletop, overhead mounting methods. When selecting a mounting location for the display unit keep the following in mind. Keep the display unit out of direct sunlight. The temperature and humidity should be moderate and stable. Locate the unit away from exhaust pipes and vents. The mounting location should be well ventilated. Mount the unit where shock and vibration are minimal. Keep the unit away electromagnetic field generating equipment such as motor,For maintenance and checking purposes, leave sufficient space at the sidesA magnetic compass will be affected if placed too close to the display unit. Observe the following compass safe distances to prevent disturbance to theStandard compass: 0.98 meters. Steering compass: 0.74 meters. Rubber cushions which absorb vibration (supplied) may be attached as belowRubber cushion. TM-166 No.18 black. Aline with edgeFollow the procedure below to mount the display unit on a tabletop or the overhead. Tabletop, overhead mountingFlush mounting. Note: Use supplied pan head screws when the thickness of the bulkhead is fromFigure 1-3.Refer to the outline drawing onMounting considerations. Install the antenna unit referring to the installation diagram on page D-3 or D-4. When selecting a mounting location for the antenna unit, keep in mind the following points. Select a location out of the radar beam. The radar beam will obstruct or preventThe location should be well away from a VHF antenna. A GPS receiver is interfered by a harmonic wave of a VHF antenna. There should be no interfering object within the line-of-sight to the satellites. Objects within line-of-sight to a satellite, for example, a mast, may block reception or prolong acquisition time. Mount the antenna unit as high as possible. Mounting the antenna unit as highThe length of the whip antenna for the GP-1850DF should be no longer thanDo not use a 2.

When selecting a picture advance speed, keep in mind that a fast advance speed will expand the size of the fish school horizontally on the screen and a slow advance speed will contract it. STOP freezes the display and it is convenient for observing an echo. To activate the bottom alarm the depth must be displayed. The WITHIN alarm sounds when the water temperature is within the range set; the WITHOUT alarm sounds when the water temperature is higher or lower than the range set. This alarm requires water temperature data. The offending alarm is displayed in red in the ALARM INFORMATION window. Press the soft key CLEAR ALARM to erase the alarm indication. The alarm icon remains displayed in red until all violated alarms have been acknowledged. The size of the fish school can be ascertained from the density of the display. This is because the echo travels between the bottom and the surface twice or more in shallow depths. The harder the bottom, the wider the trace. If the gain is set to show only a single bottom echo on mud, a rocky bottom will show a second or third bottom return. The range should be chosen so the first and second bottom echoes are displayed when bottom hardness is being determined. As surface turbulence is acoustically equivalent to running into a brick wall, the bottom echo will be displayed intermittently. Similar noise sometimes appears when a water temperature difference (thermocline) exists. Different species of fish tend to prefer different temperature zones, so the thermocline may be useful to help identify target fish. 200 kHz tends to show shallow thermoclines better than 50 kHz. This also occurs when the boat makes a quick turn or reverses movement. Lowering the picture advance speed may reduce the interruption. However, reconsideration of the transducer installation may be necessary if the interruption occurs frequently. To change the mode, use the presentation mode selection soft key, which is the 3rd soft key from the top.

North (zero degree) is at the top of the display and own ship is at the center of the screen. Own ship marker is a filled circle. This mode is useful for long-range navigation. When destination is set it is at the top of the screen, the north mark appears at the upper left side of the screen and points to north. Afilled triangle marks own ship’s position. The course or heading is at the top of screen at the moment the course-up mode is selected.Operate the cursor pad to shift the cursor. The cursor moves in the direction of the arrow or diagonal pressed on the cursor pad. Cursor position is displayed in latitude and longitude or Loran or Decca TDs (depending on menu setting) at the top of the plotter display when the cursor is on. The screen shifts in the direction opposite of cursor location. ZOOM IN expands the chart; ZOOM OUT shrinks it. See Table 3-1. When you insert a suitable mini chart card in the slot and your boat is near land, a chart appears. Insert the proper card and select a suitable chart scale. Chart icons appear to help you select a suitable chart scale. Table 3-1 shows the chart icons and their meanings. Press the soft key ZOOM IN to adjust chart scale. Press the soft key ZOOM OUT to adjust chart scale. These frames are called indices and they show you what parts of the chart can be enlarged in the current picture range. The areas circumscribed with smaller frames can be enlarged, but the area enclosed by the largest frame cannot. Simply place the cursor on the lighthouse or buoy mark. The services available appear at the top of the display. Selected indication is circumscribed with a red cursor. Your display should look something like the following illustration. Press the soft key BEACON INFO to show the DGPS reference station information. The higher the number the stronger the received signal. If noise is present at reception band width, the figure gets bigger. The higher the SN ratio the better the quality of the signal.

5 meter whip antenna. If the antenna cable is to be passed through a hole which is not large enough toRefasten it as shown in Figure 1-4 after running the cable through the hole. Washer Gasket (reddish brown). Shield. Clamp nut. Center pin (soldered). Connector shell. Figure 1-4 How to assemble the connectorInstalling the inside-hull mount transducer. Necessary tools. You will need the following tools. Silicone sealant. Remarks on installation. Do the installation with the boat hauled out of the water. Turn off the engine while installing the equipment. Install the transducer in the engine room. Selecting the mounting location. Keep the following points in mind when selecting a mounting location. The mounting location should be where the hull is of single-hull thickness andDo not place the transducer over hull struts or ribes which run under the hull.You will finalize the mounting location through some trial and error. The procedure for this is shown later. Center lineMounting locationFigure 1-5 Inside-hull transducer mounting locationLightly roughen the. Also, roughen the inside of the hull whereCoat the transducer face and mounting location with silicone sealant. Transducer face. Figure 1-6 Coating the transducer face with silicone sealantSqueeze outHull. SiliconeFigure 1-7 Attaching transducer to hull with silicone sealantFigure 1-10 Video sounder picture. If the bottom is displayed in red and the light-blue color appears the mountingYou can leave the transducer in position. If the bottom is not displayed in reddish brown, the mounting location is unsuitable. Relocate the transducer and do the following.Final preparation. Support the transducer with a piece of wood to keep it in place wile it is drying. LetTransducer mounting location.

This type of mounting provides the best performance of all, since the transducerThe performance of the video sounder is directly related to the mounting locationThe installation should beAir bubbles and turbulence caused by movement of the boat seriously degradeThe transducer should, therefore, beNoise from the propellers also adversely affects performance and the transducer should not beThe transducer must always remain submerged, even when the boat is rolling,Transducer outline drawingsShip'sFigure 1-11 Transducer outline drawingsDeep-V hull. Figure 1-12 Transducer mounting location on deep-V hull. High speed V-planing hull. Figure 1-13 Transducer mounting location on high speed. V-planing hull. Typical through-hull mount transducer installations. Fairing block. Flat washer. Rubber washer. HullHullDeep-V Hull. Flat Hull. Figure 1-14 Typical through-hull mount transducer installationsFabricate the fairing blockThe fairing block should beHole forLowerSaw along slope of hull. Figure 1-15 Construction of fairing blockNote: Do not over-stress the stuffing tube and locking nuts through excessive tight-There are two methods of installation: flush with hull (for flat hulls) and projectingDeep V-hull. Figure 1-16 Transom mount transducer mounting locations. Installing the transom mount transducer flush with hullA suitable mounting location is at least 50 cm away from the engine and where theNote: If necessary, to improve water flow and minimize air. This may require a certain amountM5 x 20. Tape. No. 1 M5 x 14. Figure 1-17 Transom mount transducer, mounting flush with hull. Installing the transom mount transducer projecting from hullThis method is employed on deep-V hulls and provides good performance because the effects of air bubbles are minimal. Install the transducer parallel withIf the boat is placed on a trailer care must beM5 x 20. M5 x 20. No. 2. M5 x 14. Figure 1-18 Transom mount transducer, projecting from hull. Transducer preparation.

Before putting the boat in water, wipe the face of the transducer thoroughly with aThis will lessen the time necessary for the transducer toDo not paint the transducer. Performance will be affected.The triducer is designed for thru-hull mounting. Mounting considerations. When selecting a mounting location keep the following points in mind. Air bubbles and turbulence caused by movement of the boat seriously degradeThe transducer should, therefore, beNoise from the propellers also adversely affects performance and the transducer should not beThe transducer must always remain submerged, even when the boat is rolling,Transom mount water temperature sensorWhen the cable is led in through the transom board, make a hole of approx. 17After passing the cable, fill the hole with aMount sensorFigure 1-20 How to install transom mount water temperature sensor T-02MTBThe sensor does not have to be installed perfectly perpendicular. The sensor must not be damaged in dry-docking operation. Select a place apart from equipment generating heat. Select a place in the forward direction viewing from the drain hole, to allow forSelect a place free from vibration. Mount the sensor as shown below. Figure 1-21 Thru-hull mount water temperature sensorsSelect a mid-boat flat position. The sensor does not have to be installed perfectly perpendicular. Select a place in the forward direction viewing from the drain hole, to allow forSelect a place free from vibration.LocknutCoat withAll wiring are terminated at the rear of the display unit. Antenna unitDisplay unit (back)Earth terminal. Ground. GroundDGPS beacon receiverRS-232C only). White. Transducer. Figure 2-1 Display unit, rear view. Power cable. Connect the power cable to the power connector. Connect the leads to the batteryConnect the antenna cable to the ANT connector. Connect the transducer cable to the XDR connector. The display unit contains several. CPUs.

While they are operating, theyGround the equipment toThe groundingConnect theIf this is not practical, the engine block can be used.Note: Use a “closed” lug to make the ground connection at the display unit. Do notThe standard cable is 10m long. For extension, in case of the GPA-016, GPA-018Fabricate the end of the antenna cable and attach the coaxial connector. Details are shown on next page. Antenna UnitConversion. Cable Assy. Antenna CableTo display unit. Fabricate locally. (See next page.). Figure 2-3 Cable extensionWrap connector with vulcanizing tape and then vinyl tape. Bind the tape endFigure 2-4 Waterproofing connectorOuter Sheath. Armor. Dimensions in millimeters. Inner Sheath ShieldExpose inner sheath and shield by the dimensionsCut off insulator and core by 10mm.Ship on clamp nut, gasket and clamp as shown left. Clamp. Nut. Gasket ClampAluminum Foil. Fold back shield over clamp and trim. Trim shield here. InsulatorFold back aluminum foil onto shield and trim. Trim aluminumPin. Clamp Nut. Shell. Solder throughSlip the pin onto the conductor. Solder them togetherInsert the pin into the shell. Screw the clamp nut intoDo not tighten byFigure 2-5 Fabrication of coaxial cableNMEA portNote 1) You cannot setup sentences when you select RTCM104 as the format. Note 2) For RS-422 format, the level converter (IF-1432) is required for connectionSelect output data sentences for external equipment as follows.Port. Format. InputVer. 1.5. Data. WPL: GP talker onlyNMEA Ver 2.0: DPT. WPL: GP talker onlyNMEA Ver 2.0: DPTFigure 3-4 Antenna Height DisplayThis setting may not be done when AUTO MODE is selected.Figure 3-8 Beacon Frequency DisplayFor example, if the depth readout from the draft to the transducer is 5 feet lowerSpeed SourceRefer to next page.

Run the boat at various speeds and watch the speed readout at the bottom ofTemperature AdjustmentWatch the water temperature readout at theThe adjustment range isFor details, see the interconnection diagram at the end ofAttach the TX power label (supplied) to the place shown below, and draw a lineBetweenAttach TX POWER. Label to here. Warning Label. Figure 3-14 Display unit, top view. To change to 1 kW power, do the following:DGPS, NMEA and power supplyNuts. Binding screws. M3x10, 10 pcs. Cover assembly. Connector gasket. Figure 3-15 Removing cover assemblyNote: Confirm that the following parts are attached. GN gasket. Shield gaskets. Figure 3-17 Inside of the coverNo. 6:The DGPS beacon receiver GR-7000A can be incorporated in the GP-1850F to provide itSix installation kits are available as shown.Type. Code No.Name. Antenna UnitReceiverReceiverAssy.Assy.TypeName. Antenna UnitReceiverReceiverAssy.Assy.ProcedureNut, washer. Nuts. Connector gasketFigure 4-1 Removing cover assemblyProcedureANLG BoardConnector. RemoveMAIN BoardANLG board, loosening two screws at TR fixing plates and disconnecting theANLG Board. Mini pinScrews (3 X 8), 3pcs. Heat Sink. TR fixing plate. Figure 4-3 Chassis assemblyScrews (3 X 8), 4pcs. DGPS Beacon receiverFrom GN-7707. S.FL2-2LP0.7-D-WHT (250) (Supplied with DGPS kit). Figure 4-5 Connecting the coaxial cables in GR-7000AReattach this tape asDGPS connection. To J8 of. ANLG BoardS.FL2-2LP0.7-D-WHT (250), 8P connector cable and 6P connector cable byFix cable assy. S.FL22LP0.7-D-WHT (250) with vinyl tape.MAIN BoardANLG BoardCableConnect 8P connector and 6PMAIN BoardA viewAssembly. Figure 4-8 Attaching chassis assemblyNut. WasherNuts. Figure 4-9 Remounting the cover. Note: When reattaching the cover, confirm the following parts are attached. Inside of the cover: Shield gaskets, GN gasket (See Figure 4-10.). On ANLG Board: Connector gasket (See Figure 4-1.)Shield gaskets. Figure 4-10 Inside of the cover.

furuno gp 500 manual

An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Furuno GP-500, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Furuno service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Furuno GP-500. After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid. Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Furuno GP-1670F owners to properly answer your question. Ask a question About the Furuno GP-1670F This manual comes under the category Navigators and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Furuno GP-1670F or do you need help. Ask your question here Furuno GP-1670F specifications Most brands periodically update the maps.ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free. ManualSearcher.

• furuno gp 500 manual, furuno gp 500 manual, furuno gp 500 manual pdf, furuno gp 500 manual download, furuno gp 500 manual 2017, furuno gp 500 manual instructions, furuno gp 150 manual.

Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. There could be errors in price, dimensions, or description. All information must be confirmed directly by the seller. This site is not liable for any mistakes. Be very wary if they request payments by Western Union or other payment methods without guarantees. Otherwise, we'll assume you're OK to continue. The cookies collect information in an anonymous form. These sophisticated components are contained within a rugged, compact case. Unique design elements make the PG-500 virtually maintenance-free and easy to install. If you have ANY questions please always feel free to send an eBay message or call Max Marine Electronics Inc, Pompano Beach, Florida for help, assistance or more detailed information. We always want to be transparent with our customers and fully disclose any information regarding the products we sell. A solution-minded staff, well versed in product functionality, compatibility and repair, is key to your satisfaction. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction. Therefore, in an instruction of Furuno GP-500 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities.A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

com If you continue to use this site we will assume that you are happy with it. Read more Ok.

furuno gp-150 operator s manual

Event marks are numbered from 01 to 99; 01 is the latest event mark. Note: You cannot register a MOB position or event position when there are no MOB positions or event positions saved. The display now looks something like the one below. 32 32.22’N 133 41.853’W JUN 6’. The message shown in Figure 4-12 appears if the waypoint is currently selected as destination, is part of a route, or is in the route currently selected as destination. The sequence of waypoints leading to the ultimate destination is called a route. The GP-150 can automatically advance to the next waypoint on a route, so you do not have to change the destination waypoint repeatedly. Selected waypoint number appears on the route editing screen. The display shown in Figure 4-17 appears if the route is in use. 1st line Are you sure to erase ? ENT: Yes. Note: Previous destination is cancelled whenever a destination is set. Setting destination by cursor Using the cursor you may set a destination consisting of 30 points. Waypoints are connected with a line. The buzzer sounds and the message shown in Figure 5-8 appears to alert you when there is no MOB position or event position. Own ship position becomes starting point and a dashed line runs between it and the waypoint selected. Using Figure 5-14 as an example, your ship is currently heading toward waypoint 04 but is to switch course and head to waypoint 03. The message shown in Figure 5-17 appears if the waypoint is currently selected as destination, is part of a registered route, or is part of the route currently being navigated. However, cross track error is calculated by rhumb line only. Great Circle: The great circle courseline is the shortest course between two points on the surface of the earth. The range, bearing and time-to-go between two points appear on the display. Own ship tracks, at the speed selected, a figure eight course, starting from position entered. All controls are operative; you may change course, enter marks, etc.

• furuno gp-150 user manual, furuno gp-150 operator s manual, furuno gp-150 operator s manual pdf, furuno gp-150 operator s manual download, furuno gp-150 operator s manual free, furuno gp-150 operator s manual 2017.

This equipment uses high voltage electricity which can shock, burn or cause death. Only qualified person- nel should work inside the equipment. Do not dissasemble or modify the equipment. Fire, electrical shock or serious injury can result. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. For 60 years FURUNO Electric Company has. Selects display mode. Registers waypoints and routes. Inscribes mark on the display.The display shown in Figure 1-3 appears.This portion of track does not appear on Own ship the display. Ship’s track while recording is stopped Recording of track turned off Figure 2-3 Track not plotted or recorded when plotting is stopped Erasing Track. Selecting Track Plotting Interval The plotting interval determines both how the track will be reconstructed on the display and track storage time. The default memory setting stores 1,000 points each of track and marks. CAUTION All data are erased whenever the memory apportion setting is changed, even when the previous value is re-entered. Magnetic bearing is true bearing plus (or minus) earth's magnetic deviation. Displaying true or magnetic bearing The default setting displays true bearings. 1) Press the MENU ESC key. You may inscribe a mark anywhere, in one of 13 shapes. Further, marks can be connected with lines. Note 1: When the mark memory becomes full no marks can be entered. Event marks can be saved as ordinary marks and the unit automatically numbers them from 01 to 99. Note 1: When the mark memory becomes full no event marks can be entered. When this occurs, the buzzer sounds and the message shown below appears on the display for three. To mark man overboard position, press the EVENT MOB key more than three seconds. When the key is pressed, the position at the exact moment the key is pressed automatically becomes the destination. The GP-150 can store 999 waypoints, numbered from 001-999.The display shown in Figure 4-5 appears.

Sentence description AAM-Waypoint arrival alarm 20P8192 MJ-A6SRMD FL15. FURUNO Electric Co., Ltd. believes identifying these components is of no value for shipboard maintenance; therefore, they are not listed in the manual. Major modules can be located on the parts location photos on the next page. CBAS provides GPS signal corrections to SBAS users, for even better position accuracy, typically better than three meters. There are three more SBAS providers, MSAS (Multi-Functional Satellite Augmentation System) for Japan, EGNOS (Euro Geostationary Navigation Overlay Service) for Europe and GAGAN (GPS And GEO Augmented Navigation) for India. Do not open the cover of the equipment. Use of the wrong fuse can cause fire or equipment damage. This equipment uses high voltage electricity which can No single navigation aid (including this shock, burn or cause death.The display shown 1) Press the DISPLAY SEL key. The display in Figure 1-3 appears.You may enlarge and shrink the display on The cursor moves in the direction of the the Plotter 1, Plotter 2 and Highway displays, cursor pads pressed. When the cursor with the ZOOM IN and ZOOM OUT keys. The reaches the edge of the display, the display horizontal range is available among The MAIN is stopped. 123 nm MENU appears.Are you sure to erase ? 4) Press to select Time. 5) Enter plotting interval in four digits. Plotting interval by distance The setting range for plotting by distance is 2.9 Selecting Track Plotting 0.00 to 99.99 nautical miles. To plot Ship's course and bearing to waypoint may This causes a difference between the true be displayed in true or magnetic bearing.This difference Magnetic bearing is true bearing plus (or is called magnetic variation, and varies with minus) earth's magnetic deviation. Page 4 SAFETY INSTRUCTIONSFOREWORD. v 6. SETTING UP VARIOUS DISPLAYS. SYSTEM CONFIGURATION. vi 6.1 The Data Display. Page 6 TABLE OF CONTENTSA Word to GP-150-DUAL The main features of the GP-150-DUAL are. Owners.

The alarm icon also appears on the Plotter 1, Plotter 2 and Highway displays. Alarm Own ship’s setting position Destination waypoint Figure 7-4 How the anchor watch alarm works Before setting the anchor watch alarm, set present position as destination waypoint, referring to chapter 5. In: Alarm sounds when speed is within range set. This alarm requires temperature signal from external equipment. 1) Press MENU ESC and 4. 2) Press to select Water TEMP. 3) Press to select In (or Over). ANT Height Enter the height of the antenna unit above sea surface (000-999 ft, 000-304 m). The default setting is 16 ft. POSN Offset You may apply an offset to position generated by the internal GPS receiver, to compensate for difference between GPS position and chart position. Time DIFF The GPS system uses UTC time. Entering speed averaging 1) Press MENU ESC, 9 and 6. 2) Press to select Speed Average. Grid tone The grid can be displayed in light or dark tone, or turned off. 1) Press MENU ESC and 1. The DISPLAY SETUP menu appears. The message shown in Figure 8-14 appears while data is being loaded. MENU:Stop Figure 8-14 14) Operate the computer to output data. When data is loaded, the cursor shifts to Stop. Saving data to personal computer Waypoint and route data can be saved to a personal computer. 1) Press MENU ESC, 9 and 5. 2) Press to select Level. Number, bearing and elevation angle of all satellites in view of the GPS receiver appear. Satellites being used in fixing position are circled with a solid line; satellites not being used in fixing position are circled with a dashed line. When you clear the plotter memory, all track and marks are cleared and all corresponding defaults settings are restored. Press the CLEAR key to silence the buzzer. If the CLEAR key is not pressed, several. If normal operation cannot be restored, ask your dealer for advice.Each time the key is pressed one of the patterns shown in Figure 9-12 appears.

MENU SETTINGSMenu description During position fixing, ship’s velocity (speedSAFE: GPS signal is safe to use. Setting up the GPS SETUP menu. CAUTION: RAIM accuracy is. Page 53 8. MENU SETTINGS. GPS position smoothing RAIM accuracyTime difference 2) Press to select Unit of Distance.Enlarging characters 8.4 Outputting Data. The size of the indications of position or Besides its fundamental function. Page 57 8. MENU SETTINGSStopping loading of dataThe message DGPSReferenceDOP error Self test error messageThe table which follows providesDisplay test Automatic testingPage 69: 10. INSTALLATION 10. INSTALLATIONAn optional flush mount kit type S is required. (Name: Flush Mount Kit S, Type. OP20-24,. Page 72 10. INSTALLATIONMountingTaping antenna unit GPA-018SExtending antenna cable lengthHow to attach the N-P-8DFB connector. Outer SheathCross-track error,DATA1 output settingDATA 3 output setting. Setting DATA 4 to Data OutputSetting DATA 4 to DGPSSpecificationsPin no. Designation Pin no. Designation Pin. Page 90 10. INSTALLATION. LED statusPage 91: APPENDIX APPENDIX. Menu Tree. Main menuPage 94 APPENDEX. World Time StandardsLoran C ChainsDecca ChainsParts List. This equipment contains complex modules in which fault diagnosis and repair down toPage 99 APPENDEX. Parts Location. Display unitInterface DocumentationAntenna Cable SetAntenna Cable SetFeb. 19, '03Feb. 19, '03Feb. 19, '03Jan.13'04INDEX cancelling 5-5A setting through waypoint list 5-3. Page 121 INDEX. F Memory. Fix mode 8-2 apportioning 2-5G testing 9-5. Geodetic chart list AP-5 Menu tree AP-1. Page 122 T X. Time difference 8-4 XTE alarm. See cross track error (XTE) alarm. Time mark tone 8-5. Track Y. Hazardous voltage which canTurn off the power at thePost a sign near the switchFire, electrical shock orConfirm that the power supply voltageConnection to the wrong power supplyUse the correct fuse. Use of a wrong fuse can cause fire orKeep the following compass safeStandard Steering.

Congratulations on. Page 8: SYSTEM CONFIGURATION SYSTEM CONFIGURATIONThe GP-150-DUAL. Page 11 1. OPERATIONAL OVERVIEWPlotter 1 display Plotter 2 displayNavigation display 2) Autopilot connected, automatic modeData display Transmitting data. Refer to Chapter 6 for user-defined window To mutually transmit data, do the. Page 15 1. OPERATIONAL OVERVIEWThe Interface Unit IF-2500 outputs dataCursor turned off 2.4 Shifting the Display. Ship's position (in latitude and longitude or The display. Page 19 2. DISPLAY AND TRACK. When plotting is stopped 2.7 Erasing TrackMagnetic variation. The location of the magnetic north pole isMarks can be inscribed on the Plotter 1 and. Plotter 2 displays,. Page 24 3. MARKSSelect mark Event marks can denote. Page 25 3. MARKSThis page is intentionally left blank.Control is returned to the last-used displayEntering waypoints by MOB Entering waypoints at own ship's. The MOB position or. Page 30 4. NAVIGATION PLANNING. Erasing waypoints through the 4.4 Entering RoutesRoute waypoints are. Page 34 4. NAVIGATION PLANNING. This page is intentionally left blank.There are four ways by which you can set 1) Press. Page 36 5. SETTING DESTINATIONSetting destination by MOB position or Setting destination through waypointNote: This operation. Page 38 5. SETTING DESTINATIONSkipping route waypoints 2) Press or to select route waypointYou may skip route. Page 40 5. SETTING DESTINATIONThe user may select what. Page 44 6. SETTING UP VARIOUS DISPLAYSPosition can be displayed in latitude and 6). Page 45 6. SETTING UP VARIOUS DISPLAYS. Entering waypoints using LOPs 5) Key in LOP1 and LOP2, to enableThere are seven alarm conditions which Watch AlarmAnchor watch alarm 7.3 Cross Track Error (XTE). The anchor watch alarm sounds to warn you AlarmThe speed alarm sounds when ship's speed The trip alarm sounds. Page 50 7. ALARMSThe water temperature alarm sounds. Page 51: 8. MENU SETTINGS 8.

0 kHz). Press W or X to select baud rate; 25, 50, 100 or 200 bps. Press the MENU ESC key. Nearest DGPS station list. The STATION NEAREST LIST shows the five closest DGPS beacon stations, includingFor user-programmed stations, see Operator’s Manual.Press S or T to select Ref. Station. Press X to select List. After the message “PLEASE WAIT” appears, the following list is shown. AsteriskedENT: Enter. NoYesMENU: EscapeBit Rate: 200 bps. SNR: 21 dB. Sig Strength: 83 dBThis value is between 1 to 22. The higherWhen the ship is in the service area of aGood. GoodDGPS signal strength. This value is between 1 and 84. The higher the value, the stronger the signal. If a noise appears at reception bandwidth,When GPS is malfunctioning though DGPS is normal. The GP-150 can output navigation information to external equipment. For example, it canBefore selecting data to output, confirm what data the external equipment requires. OutputTalker. All data transmitted by marine electronics equipment is prefixed with a two-character codeThis two-character codeThe GP-150 contains the talkers GP, LC and DE. Because GPS is a relatively new system some early model equipments do not recognizeAutopilot sentence BBOD: Bearing-origin to destination. BWC: Bearing and distance to waypoint-great circle. BWR: Bearing and distance to waypoint-rhumb line. BWW: Bearing-waypoint to waypoint. DTM: Datum reference. GGA: Global positioning system (GPS) fix dataGBS: GPS satellite fault detection. RMB: Recommended minimum navigation information cross track error, direction to steer,UTC of position fix, latitude and longitude, ground speed and course, date,RTE: Routes. VDR: Set and drift. VTG: Course over ground and ground speed. WCV: Waypoint closure velocity. WPL: Waypoint location. XTE: Cross-track error, measured. ZDA: Time and date. Rnn. Routes. Also, following NMEA 0183 Ver. 1.5 sentence is output.Note: BWC, BWR, GGA, GLL, RMB, RMC or WPL is required to output DTM.Talker ID is not distinguished.

DBT: Depth below transducer. DPT: Depth. HDG: Heading, deviation and variation. HDM: Heading, magnetic. HDT: Heading, true. MTW: Water temperature. TLL: Target latitude and longitude. VHW: Water speed and heading. FURUNO proprietary sentence. AGFPA: Autopilot information from FURUNO autopilot equipments.PortOutputDATA3 External MOBDATA4 DGPS or general data (Selected. General dataVer.2.0Note: BWC, BWR, GGA, GLL, RMB, RMC or WPL is required to output DTM. General dataConnect YEOMAN equipment to DATA4 port. TX Rate of operation. The TX rate of operation is the percentage of data output in one second, and it appears onTX rate of operation: High. Note 1: When outputting data without rest intervals between data, TX rate of operation isThus, do not output unnecessary data or set TXNote 2: When the external equipment cannot display correct data input from the GP-150,For example, set a rate of operation lessDATA3. Log PulseENT: Enter. TX rate of operation. MENU: Escape. This line appears only when LOG isSettings shown above are default settings. DATA 1, 3 OUTPUT SETUP menuPress W or X to select V1.5, V2.0 or IEC. Talker ID appears in reverse video. Press W or X to select GP, LC or DE. Enter Tx interval for each output data sentence in line 1. Tx interval is available in 00,ENT key after setting each line. In great circle navigation, BWC and WNC are output but BWR and WNR are not. In rhumbThe total data output are shown by percentage on the third line.ENT: Enter. Setting shown here are default settings. DATA 2 OUTPUT SETUP menuDATA 3 output settingSelection of NMEA0183 or log pulse. Output data. NP boardLog pulse. Rate of log pulse outputPress S or T to select “DATA 3. Log Pulse”. Press W or X to select log pulse for external equipment; 200 ppm or 400 ppm. Press the MENU ESC key.DATA 4. Level. Data. To Next Page. ENT: EnterMENU: Escape. Appears only when external. DGPS receiver is used.Press W or X to select level of external equipment; RS232C or RS422.

Display unitThis page is intentionally left blank.Autopilot etc. Display Unit. DGPS Beacon. ReceiverName. Antenna Unit. Installation. Materials. Accessories. Spare Parts. TypeRemarksWithout Beacon RX. With Beacon RX. With Antenna Cable. See lists. Without Antenna CableOptions. Name. Flush Mount Kit S. Flush Mount Kit F. Antenna Cable Set. Antenna Cable Assy. Right Angle Antenna. Base. L-Type Antenna Base. Handrail Antenna Base. Mast Mount Kit. Cable Assy. TypeNo.13-RC5160For display unit.For antenna unit.Whip Antenna. Printer. Data Switch BoxWith whip antenna and OP20-32-1. With GPS-019S. Without whip antenna. For 100VAC mains. For 220VAC mainsRefer to theLocate the unit away from exhaust pipes and vents. The mounting location should be well ventilated. Mount the unit where shock and vibration are minimal. Keep the display unit away electromagnetic field generating equipment such as motor,Table Top and Overhead MountingFlush mounting type F. An optional flush mount kit type F is required. For details, see outline drawing at end of thisName. Self-tapping screw. Hex. bolt. Spring washer. Cosmetic panel. TypeAn optional flush mount kit type S is required. (Name: Flush Mount Kit S, Type: OP20-24. Code No.: 004-393-000). Wing bolt. Wing nut. Flush mount metal. TypeInstall the antenna unit referring to the installation diagram at end of manual. WhenThe radar beam will obstruct or prevent receptionObjects within line-of-sight toMounting the antenna as high as possible keeps it freeConnect ground wire of 1.25 sq or largerSee next page. Coat here with silicone sealant toWrap the vinyl sheet to preventAfter inserting the whip antenna to the antenna base of GPA-018S, tape the antenna baseHow to wrapBase. Whip antenna. Antenna. Butyl rubber tapeKeep tension on edge of tape, using finger to hold tape. Then, squeeze edges of tapeWrap approx.How to wrapWhite vinyl tapeThe standard cable is 15m long.

30m and 50m long extension cable sets are optionallyFabricate the end of antenna cable and attach the coaxial connector. Details are shownAntenna UnitCode no.Conversion Cable Assy. Antenna CableFor CP20-01700, CP20-01710To display unit. Fabricate locally. (See the next page.)Antenna CableFor CP20-02700, CP20-02710To display unit. Fabricate locally. (See the next page.). Extension Cable Line-up. Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end withHow to waterproof the connector of the antenna cableOuter Sheath. Armor. Inner Sheath ShieldExpose inner sheath and shield by the dimensionsCut off insulator and core by 10mm.Clip on clamp nut, gasket and clamp as shown left. Clamp. Nut. Gasket ClampAluminum Foil. Fold back shield over clamp and trim. Trim shield here. InsulatorFold back aluminum foil onto shield and trim. Trim aluminumPin. Clamp Nut. Shell. Solder throughSlip the pin onto the conductor. Solder them togetherInsert the pin into the shell. Screw the clamp nut intoDo not tighten byAntenna UnitRear of Display Unit. Ground terminalFlat washer. Crimp-on lug. Spring washerWing boltRedThe display unit contains several CPUs. While they are operating, they radiate noise, whichGround the unit as follows to prevent it. External Equipment. The DATA1, DATA2, and DATA3 ports are used to connect an external equipment such asRefer to the interconnection diagram onThe DATA4 port is used toConnection of DATA4 port. In case of RS-422 LevelNMEA equipment. In case of RS-232C LevelNMEA equipment. See page 19.DGPS function is provided.SRAM, Internal Battery, GPS and BEACON. DGPS Setup. Automatic DGPS setup. GP-150 can automatically select optimum reference station. If it takes more than five (5)Freq. Baud Rate. ENT: Enter. Auto ManMENU: Escape. DGPS SETUP menuManual DGPS setup. Enter frequency and baud rate of station.Press S or T to select Ref. Station. Press X to select Man. Press T to select Freq. Enter frequency in four digits (283.5 kHz to 325.

Press W or X to select Out. Press T to select to Next Page.Data Fmt. Talker IDENT: Enter. MENU: EscapeWaypoints and Routes data can be received from a personal computer, through the DATAPress S or T to select DATA4. Level. Press W or X to select level of personal computer; RS232C or RS422. Press X to select Com. Press T to select To Next Page. To Previous Page. Baud RateLLoad Data. Command. Stop. Start. Save Data. StartENT: Enter. MENU: EscapeStop, on the same line as Command, appears in reverseThe message shown in figure below appears. Loading erases current dataAre you sure to load? ENT: Yes MENU: No. The message shown in below appears while data is beingNow loading. MENU: StopWhen loading data is completed, the cursor shifts to. Stop.Setting DATA 4 to DGPS. An external DGPS receiver can be connected to the DATA 4 port. Follow the procedure below to setup the GP-150 according to the specifications of the. DGPS receiver.Press S or T to select Level. Press W or X to select level; RS232C or RS422. Press W or X to select DGPS. To previous Page. First Bit. Parity. Stop Bit. Baud RateENT: Enter. MENU: EscapeAntennaWhen the GP-150 is connected with Beacon Receiver GR-80, do the setting as follows. Signal level. First BitRefer to page 22 for DGPS setup.Nishinomiya, 662-8580, JAPAN. Fax. All rights reserved. Printed in Japan. No single navigation aid (including this unit) should ever be relied upon as the exclusive means for navigating your vessel. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. Thereafter it t akes about 12 seconds to find position each time the power is turned on. The display shown in Figure 1-3 appears. The default memory setting stores 1,000 points each of track and marks. Magnetic bearing is true bearing plus (or minus) earth's magnetic deviation. Y ou may inscribe a mark anywhere, in one of 13 shapes. Event marks can be saved as ordinary marks and the unit automatically numbers them from 01 to 99.

T o mark man overboard position, press the EVENT MOB key more than three seconds. Event marks are numbered from 01 to 99; 01 is the latest event mark. The display shown in Figure 4-17 appears if the route is in use. 1st line Are you sure to erase. Own ship tracks, at the speed selected, a figure eight course, st arting from position entered. WGS-84 (standard GPS chart system) and NAD 27 can be directly selected. Grid tone The grid can be displayed in light or dark tone, or turned off. 1) Press MENU ESC and 1. The message shown in Figure 8-14 appears while data is being loaded. Clearing the plotter memory The plotter memory holds plotted track and mark data. Check the item s mentioned below monthly to keep the equipment in good working order. If the CLEAR key is not pressed, several beeps sound every three minutes.DOC-859 Declaration of c o n f o r m i t y We FURUNO ELECTR IC C O. View and Download Furuno GP-1650 operator's manual online. GP-1650 Marine GPS System pdf manual download. Furuno GP-1650DF Pdf User Manuals. View online or download Furuno GP-1650DF Operator's Manual FURUNO equipment. Features The GP-1650WD provides a totally integrated DGPS beacon receiver, WAAS function, GPS receiver and color video plotter. The GP-1650W mostly shares the same features with the GP-1650WD except it does not have a DGPS beacon receiver. Navigation information is displayed on a bright 5.6-inch color TFT LCD. On-screen WARNING. Do not work inside the equipment unless totally familiar with electrical circuits. Hazardous voltage which can shock, burn or cause serious injury exists inside the equip Auto and car manuals and free pdf automotive manual instructions.User manual for the device Furuno GP-1650WD. Online user manual database Furuno GP-1650WD GPS Receiver User Manual. Furuno GP-1650 GPS Receiver User Manual. Furuno GP-1650WF GPS Receiver User Manual Auto and car manuals and free pdf automotive manual instructions.

Find the user manual you need for your automobile and more at ManualsOnline To get DGPS GPS NAVIGATOR. GP-150. OPERATOR'S MANUAL www.furuno.co.jp. MODEL Display Unit. Radar, Echosounder.

furuno gp 90 installation manual

For example, set a rate of operation less than 60 % for the Temperature Indicator TI-20. The DATA 1, 3 OUTPUT SETUP menu appears. Data Fmt. Output Data DATA3. Log Pulse ENT: Enter Figure 5-3 DATA 1, 3 OUTPUT SETUP menu 2) Press to select Data Fmt. 3) Press to select V1.5, V2.0 or IEC. The DATA 2 OUTPUT SETUP menu appears. Data Fmt. Output Data ENT: Enter Figure 5-4 DATA 2 OUTPUT SETUP menu 2) Follow the procedure for setting DATA 1 output.Setting DATA 4 to DGPS An external DGPS receiver can be connected to the DATA 4 port.All rights reserved. Pub. No. IME-44270-C1 Pub. No. IME-44270-C1 ( ( HIMA HIMA ) ) GP-90 GP-90 The paper used in this manual is elemental chlorine free. StandardsThe display unit can be installed with either of four methods as shown below. Refer to the. Page 5: 3. ANTENNA UNIT 3. ANTENNA UNIT. Mounting. Install the antenna unit referring to the installation diagram at end of manual. WhenHow to attach the N-P-8DFB connector. Outer SheathThe figure below shows the connection of cables on rear of display unit.Grounding. The display unit contains several CPUs. While they are operating, they radiate noise, whichChecking OperationManual DGPS setup. Enter four. Page 11 5. INITIAL SETTINGS. The GP-90 can output navigation information to external equipment. For example, it canData format and data output availability. Checksum is checked if attached, and if any. Page 14 5. INITIAL SETTINGS. AGFPA: Autopilot information from FURUNO autopilot equipmentsDATA 1 output setting. The DATA 1, 3 OUTPUT SETUP. Page 16 5. INITIAL SETTINGS. DATA 2 output setting. The DATA 2 OUTPUT SETUP menu appears. Page 17 5. INITIAL SETTINGS. Setting DATA 4 to Data Output. Setting DATA 4 to “COM.” (general data). Waypoints and Routes data can be received from a personal. Page 19 5. INITIAL SETTINGSWhen loading data is completed, the cursor shifts toBeacon Receiver Set GR-80After inserting the whip antenna to the antenna base of GPA-018S, tape the antenna base.

• furuno gp 90 installation manual, furuno gp 90 service manual, furuno gp 90 manual, furuno gp 90 installation manual, furuno gp 90 installation manual pdf, furuno gp 90 installation manual download, furuno gp 90 installation manual instructions, furuno gp 90 installation manual 2017.

Hazardous voltage which can cause electrical shock, burn or serious injury exists inside the equipment. Turn off the power at the mains switchboard before beginning the installation. Post a sign near the switch to indicate it should not be turned on while the equip-. Refer to the outline drawing at the end of manual. Locate the unit away from exhaust pipes and vents. The mounting location should be well ventilated. Mount the unit where shock and vibration are minimal. When selecting a mounting location for the antenna unit, keep in mind the following points. Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the GPS satellite signal. Clamp Gasket (reddish brown) Trim shield here. Insulator Trim aluminum tape foil here. Clamp Nut Solder through the hole. Remove outer sheath and armor by the dimensions shown left. Antenna Unit GPA-019S GPA-018S GPA-017S 20cm External Equipment CAUTION Ground the display unit to prevent loss of sensitivity and mutual interference. Rear of Display Unit DATA1 DATA2 DATA3 DATA4. While they are operating, they radiate noise, which can interfere with other radio equipment. Ground the unit as follows to prevent it. The grounding wire should be 1.25sq or larger. The grounding wire should be as short as possible. External Equipment The DATA1, DATA2, and DATA3 ports are used to connect an external equipment such as autopilot, remote display, navigation equipment. If it takes more than 5 minutes to fix DGPS position at the automatic mode, switch to manual mode. Use the manual mode when an external beacon receiver has no automatic function of station selection. Before selecting data to output, confirm what data the external equipment requires. Output necessary data only. FURUNO proprietary sentence AGFPA: Autopilot information from FURUNO autopilot equipments. When the external equipment cannot display correct data input from the GP-90, the rate of operation should be lowered.

Keep the display unit away electromagnetic field generating equipment such as motor,Table Top and Overhead MountingFlush mounting type F. An optional flush mount kit type F is required. For details, see outline drawing at end ofName. TypeAn optional flush mount kit type S is required. Flush Mount Kit SInstall the antenna unit referring to the installation diagram at end of manual. WhenThe radar beam will obstruct or prevent receptionObjects within line-of-sight toMounting the antenna as high as possible keeps it freeConnect ground wire of 1.25 sq or largerSee chapter 7 for instructions. Extending Antenna Cable Length. The standard cable is 15m long. 30m and 50m long extension cable sets are optionallyFabricate the end of antenna cable and attach the coaxial connector. Details are shownAntenna UnitCode no.Conversion Cable Assy. Antenna CableFor CP20-01700, CP20-01710To display unit. Fabricate locally. (See the next page.)Antenna CableFor CP20-02700, CP20-02710To display unit. Fabricate locally. (See the next page.). Extension Cable Line-upWrap connector with vulcanizing tape and then vinyl tape. Bind the tape end withHow to waterproof the connector of the antenna cableOuter Sheath. Armor. Inner Sheath ShieldExpose inner sheath and shield by the dimensionsCut off insulator and core by 10mm.Clip on clamp nut, gasket and clamp as shown left. Clamp. Nut. Gasket ClampAluminum Foil. Fold back shield over clamp and trim. Trim shield here. InsulatorFold back aluminum foil onto shield and trim. Trim aluminumPin. Clamp Nut. Shell. Solder throughSolder them togetherInsert the pin into the shell. Screw the clamp nut intoDo not tighten byAntenna UnitRear of Display UnitRedThe display unit contains several CPUs. While they are operating, they radiate noise, whichGround the unit as follows to prevent it. External Equipment.

Antenna Cable SetAntenna Cable SetSep.29'05Feb. 19, '03Feb. 19, '03. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Furuno GP-90 it belongs to the category GPS Receiver. A user manualFuruno GP-90 is taken from the manufacturer, a Furuno company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Furuno GP-90 directly. You can view the user manualFuruno GP-90 directly online or save and store it on your computer.If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Furuno GP-90. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Furuno GP-90 - you will surely help many users by doing so.Ask a question - our users can help you. Hazardous voltage which canTurn off the power at thePost a sign near the switchFire, electrical shock orConfirm that the power supply voltageConnection to the wrong power supplyUse the correct fuse. Use of a wrong fuse can cause fire orKeep the following compass safeStandard Steering. Display unitName. Antenna Unit. Display Unit. Installation. Materials. Spare Parts. TypeMassRemarks. For DGPSWith Beacon RX. See lists at end of. With Antenna CableWithout Antenna CableOptions. Name. Flush Mount Kit S. Flush Mount Kit F. Antenna Cable Set. Antenna Cable Assy. Right Angle Antenna. Base. L-Type Antenna Base. Handrail Antenna Base. Mast Mount Kit. Cable Assy. Beacon Receiver Set. Rectifier. DGPS Beacon. Receiver. Whip Antenna. TypeNo.13-RC5160For display unit.With whip antenna and OP20-32-1. With GPS-019S. Without whip antenna. For 100VAC mains. For 220VAC mainsRefer to theLocate the unit away from exhaust pipes and vents. Mount the unit where shock and vibration are minimal.

XTE: Cross-track error, measured. ZDA: Time and date. Rnn. Routes. Also, following NMEA 0183 Ver. 1.5 sentence is output.Talker ID is not distinguished. DBT: Depth below transducer. DPT: Depth. HDG: Heading, deviation and variation. HDM: Heading, magnetic. HDT: Heading, true. MTW: Water temperature. TLL: Target latitude and longitude. VHW: Water speed and heading. FURUNO proprietary sentence. AGFPA: Autopilot information from FURUNO autopilot equipments.PortDGPS or general dataOutput. Ver.2.0General data. Ver.2.0General dataConnect YEOMAN equipment to DATA4 port. Rate of operation. The TX rate of operation is the percentage of data output in one second, and it appears onWhen the external equipment cannot display correct data input from the GP-90, the rate ofFor example, set a rate of operation less than 60 % for the. Temperature Indicator TI-20.The DATA 1, 3 OUTPUT SETUP menu appears.Talker ID. Output DataDATA3. Log Pulse. ENT: EnterMENU: Escape. Settings shown here are default settings. This line appears only when LOG isFigure 5-3 DATA 1, 3 OUTPUT SETUP menuPress W or X to select V1.5, V2.0 or IEC. Press W or X to select GP, LC or DE. Enter Tx interval for each output data sentence in line 1. Tx interval is available in 00,In great circle navigation, BWC and WNC are output but BWR and WNR are not. In rhumbThe total data output are shown by percentage on the third line.The DATA 2 OUTPUT SETUP menu appears.Talker IDMENU: Escape. Setting shown here are default settings. Figure 5-4 DATA 2 OUTPUT SETUP menuDATA 3 output settingDATA 1 is output from DATA 3. Selection of NMEA0183 or log pulse. Output data. NAV board. JP4 (2 pcs.). JP5 (3 pcs.)Press W or X to select log pulse for external equipment; 200 ppm or 400 ppm.DATA 4. Level. Data. To Next Page. Appears only when external. DGPS receiver is used.Press W or X to select level of external equipment; RS232C or RS422. Press W or X to select Out. Press T to select to Next Page.Data Fmt. Talker IDENT: Enter.

The DATA1, DATA2, and DATA3 ports are used to connect an external equipment such asRefer to the interconnection diagram onThe DATA4 port is used toConnection of DATA4 port. In case of RS-422 LevelNMEA equipment. In case of RS-232C LevelNMEA equipmentSelf-test display at equipment start up. DGPS Setup. Automatic DGPS setup. The beacon receiver (GR-7000A) can automatically select optimum reference station byIf it takes more than 5 minutes to fix DGPS position at theUse the manual mode when an external beaconFreq.Baud Rate. These items appear whenENT: Enter. MENU: Escape. Figure 5-1 DGPS SETUP menuEnter four digit ID number, frequency and baud rate of station.Press S or T to select DGPS Station. Press W to select Man. Enter four digit ID number.DGPS Operation checkingBit Rate: 200 bps. SNR: 21 dB. Sig Strength: 83 dBWhen the ship is in the service area of aGood. GoodBeacon signal status. Reference station status. DGPS signal strength. This value is between 1and 84. The higher the value,If a noise appears at reception band width,Figure 5-2For example, it canBefore selecting data to output, confirm what data the external equipment requires. OutputTalker. All data transmitted by marine electronics equipment is prefixed with a two-character codeThis two-character codeThe GP-90 contains the talkers GP, LC and DE. Because GPS is a relatively new system some early model equipments do not recognizeAutopilot sentence BBOD: Bearing-origin to destination. BWC: Bearing and distance to waypoint-great circle. BWR: Bearing and distance to waypoint-rhumb line. BWW: Bearing-waypoint to waypoint. DTM: Datum reference. GGA: Global positioning system (GPS) fix dataGBS: GPS satellite fault detection. RMB: Recommended minimum navigation information cross track error, direction to steer,UTC of position fix, latitude and longitude, ground speed and course, date,RTE: Routes. VDR: Set and drift. VTG: Course over ground and ground speed. WCV: Waypoint closure velocity. WPL: Waypoint location.

Navigation information is displayed on a bright inch color TFT LCD. GP GPS pdf manual download. Database contains 2 Furuno GPF Manuals (available for free online viewing or downloading in PDF): Installation manual, Operator's manual. If it takes more than 5 minutes to fix DGPS position at the automatic mode, switch to manual mode. Receiver Type GP33 Spanish Operator’s Manual furuno gp 90 installation manual ( MB) pdf. Search. Furuno Installation Manual Marine Radar Model. User Manuals, Guides and Specifications for your Furuno GPF Plotter. The radar beam will obstruct or prevent reception of the GPS satellite signal. FURUNO equipment. Furuno Marine Radar Installation Manual. For over 50 years FURUNO Electric Company has enjoyed an enviable. Furuno gps receiver user manual (36 pages) GPS Furuno GP Operator's Manual. All prices shown are in USD. Display Type furuno gp 90 installation manual Color LCD. Use the manual mode when an external beacon. Power Usage VDC. username password login or register. No. GP GPS pdf manual download. View online Operator's manual for Furuno GPS Navigator GP MARK-2 GPS or simply click Download button to examine the Furuno GPS Navigator GP MARK-2 guidelines offline on your desktop or laptop computer. View online Installation manual for Furuno MFD8 Monitor or simply click Download button to examine the Furuno MFD8 guidelines offline on your desktop or laptop computer. The GP can be flush mounted in a console or panel, or mounted on a desktop. Furuno MARINE RADAR MARK 2 DISPLAY USED 0. Automatic DGPS setup The beacon receiver (GRA) can automatically select optimum reference station by feeding GP’s position data. Database contains 1 Furuno MD Manuals furuno gp 90 installation manual (available for free online viewing or downloading in PDF): Operator's manual. LC Marine GPS System pdf manual download. Furuno gp Service Manual.

Automatic DGPS setup The beacon receiver (GRA) can automatically select optimum reference station by feeding GP’s position data. Wrong oper-ation or maintenance can cancel the warranty or cause injury. The paper used in this manual is elemental chlorine free. Free shipping for many products. If it takes more than 5 minutes to fix DGPS position at the automatic mode, furuno gp 90 installation manual switch to manual mode. User Manuals, Guides and Specifications for your Furuno MD GPS. Pages: See Prices; Furuno Fish Finder GP MARK Furuno GPS Navigator Operator's Manual. Database contains 1 Furuno MD Manuals (available for free online viewing or downloading in PDF): Operator's manual. Furuno Marine Radar Installation Manual. Auto and car manuals and free pdf automotive manual instructions. Furuno GPS Navigator Operator's Manual. View and furuno gp 90 installation manual Download Furuno GP installation manual online. The high sensitivity receiver tracks up to 12 satellites simultaneously. Furuno Installation Manual Marine Radar Model. GP90 GP90D Installation manual ( MB) pdf. View online Installation manual for Furuno NAVpilot Marine Equipment or simply click Download button to examine the Furuno NAVpilot guidelines offline on your desktop or laptop computer. The GP can be flush mounted in a console or panel, or mounted on a desktop. On-screen. Manuals Directory Furuno manuals. Features The GP GPS Navigator is a totally integrated GPS receiver and video plotter consisting of a display unit and an antenna unit. Database contains 2 Furuno GP Operators Manuals furuno gp 90 installation manual (available for free online viewing or downloading in PDF): Operator's manual. Your equipment takes about 90 seconds to. The GP GPS Navigator shall be installed in accordance with the Installation manual Pub. Table top mounting Mount the display unit on a desktop using the hanger. Marine GPS System Furuno GP Installation Manual.

MENU: EscapeWaypoints and Routes data can be received from a personal computer, through the DATATo Previous Page. Baud RateLLoad Data. Command. Save Data. Stop. Start. StartENT: Enter. Stop, on the same line as Command, appears in reverseThe message shown in Figure 5-8 appears. Loading erases current dataAre you sure to load? ENT: Yes MENU: No. Figure 5-8. The message shown in Figure 5-9 appears while data is beingNow loading. MENU: Stop. Figure 5-9When loading data is completed, the cursor shifts to. Setting DATA 4 to DGPS. An external DGPS receiver can be connected to the DATA 4 port. Follow the procedure below to setup the GP-90 according to the specifications of the DGPSTo previous Page. First Bit. Parity. Stop Bit. Baud RateENT: Enter. MENU: EscapeWhip. AntennaWhen the GP-90 is connected with Beacon Receiver GR-80, do the setting as follows. Signal level. First BitRefer to page 17 for DGPS setup.How to wrapBase. Whip antenna. Antenna. Butyl tapeKeep tension on edge of tape, using finger to hold tape. Then, squeeze edges of tapeWrap approx.How to wrapWhite vinyl tapeTNC-PS-3D-15,15m,?5.3IV-2sq.Nishinomiya 662-8580, JAPAN. Telephone:Printed in Japan. So this website was intended for free download articles fromYou are self-liable for your download.You can learn how to disable cookie here. I'm looking for a manual for a Furuno GaAs furuno gp 90 installation manual FET Front End. Packing. Receiver Type WAAS or GPS. Furuno GP User Manual. Only qualified personnel should work inside the equipment. GP No Longer Available. User Manuals, Guides and Specifications for your Furuno GP Operators GPS, Marine GPS System. Furuno MARINE RADAR MARK 2 DISPLAY USED 0. Features The GP GPS Navigator is a totally integrated GPS receiver and video plotter consisting of a display unit and an antenna unit. Turn off the power at the switchboard before furuno gp 90 installation manual beginning the installation. Browse All Products. View and Download Furuno GP installation manual online.

Loran C Navigator. View furuno gp 90 installation manual online Operator's manual for Furuno GP Marine GPS System or simply click Download button to examine the Furuno GP guidelines offline on your desktop or laptop computer. GP GPS pdf furuno gp 90 installation manual manual download. View and Download Furuno LC owner's manual online. Browse the Furuno product catalog for current furuno gp 90 installation manual and previous products. User Manuals, Guides and Specifications for your Furuno GP GPS, Marine GPS System. Furuno GPS Receiver User Manual. IMEZ3 (or later version). Data Type NMEA or NMEA Display Size inches. Furuno gps receiver. GPS Furuno GP Installation Manual. View online Operator's manual for Furuno FAP GPS or simply click Download button to examine the Furuno FAP guidelines offline on your desktop or laptop computer. Furuno gp Likes 0 Downloads 10 Show. The GPW mostly shares the same features with the furuno gp 90 installation manual GPWD furuno gp 90 installation manual except it does not have a DGPS beacon receiver. Database contains 2 Furuno GP Manuals (available for free online viewing or downloading in PDF): Operator's manual. Database contains 2 Furuno GP Manuals (available for free online viewing or downloading in PDF): Installation manual, Operator's manual. Also for: Gp Manuals and User Guides for Furuno GP We have 3 Furuno GP manuals available for free PDF download: Operator's Manual, Installation Manual Furuno GP Operator's Manual (99 pages). We are confident you will see why the FURUNO name has become synonymous with quality and reliability. The paper used in this manual before beginning the installation. User Manuals, Guides and Specifications for your Furuno GP GPS. Browse the Furuno product catalog for current and previous products. Refer to the outline drawing at the end of manual. Prices and Specifications Subject to Change Without Notice. See Prices; Furuno Fish Finder GP MARK Furuno GPS Navigator Operator's Manual.

Gps navigator; dgps navigator (81 pages) Summary of Contents for Furuno GP Page 1: Table Of Contents. Pages: See Prices; Furuno Fish Finder GP The FURUNO GP is a new GPS navigator designed for SOLAS ships complying with the new GPS performance standard IMO Res MSC(73) and associated IEC standards required on and after 1 July It is a highly reliable standalone EPFS (Electronic Position-Fixing System) providing a navigation solution to the AIS, radars, VDRs, etc. Install the antenna unit referring to the installation diagram furuno gp 90 installation manual at end of manual. The FURUNO GP is a new GPS furuno gp 90 installation manual navigator designed for SOLAS ships complying with the new GPS performance standard IMO Res MSC(73) and associated IEC standards required on and after 1 July It is a highly reliable standalone EPFS (Electronic Position-Fixing System) providing a navigation furuno gp 90 installation manual solution to the AIS, radars, VDRs, furuno gp 90 installation manual etc. Furuno GP GPS manual free download. I'm looking for a manual for a Furuno GaAs FET Front End. CAUTION Observe the following compass safe furuno gp 90 installation manual distances to prevent interference to a magnetic compass: Use the power cable supplied with the. Find best value and selection for your Furuno GaAs FET Front End Marine Radar Mark 2. Furuno GP Installation Manual Installation manual (44 pages) Furuno LC MARK-II User's Manual. Recognized languages: English: Pages: Size: MB: Type the characters you see in the picture. Fire or electrical shock can result if the power is left on. Full screen Furuno. GP Manual. Browse the Furuno product catalog for current and previous products. An 8-state Kalman filter ensure optimum accuracy in determination of vessel position, course and speed. Browse All Products Power Usage 12 VDC or 24 VDC. Find best value and selection for your Furuno GaAs FET Front End Marine Radar Mark 2.

Table top mounting Mount the display unit on a desktop using the hanger. GPS Furuno GP Installation Manual (66 pages) GPS Furuno GPF Operator's Manual. Download Like. LC furuno gp 90 installation manual GPS pdf furuno gp 90 installation manual manual download. If it is thicker than those dimensions, the length of 90 MSD Unit: mm Thru-hull mount transducer mounting dimensions (millimeters) 8. Browse the Furuno product catalog for current and previous products. LC GPS pdf manual download. NOTICE Do not apply paint, anti-corrosive sealant or.